Honda Ridgeline. Manual — part 242
08
09
10
11
14-353
A
B
C
D
E
F
E
D
D
D
D
C
C
C
D
E
F
D
E
D
C
D
C
D
A
B
A
B
C
10. Install the disc spring (A) in the 4th clutch drum (B)
in the direction shown. Starting with the 4th clutch
flat-plate, alternately install the flat-plates (C) (3)
and discs (D) (3), and alternately install the wave-
plates (E) (2) and discs (D) (2). Install the clutch end-
plate (F) with the flat side down on the top disc.
11. Install the disc spring (A) in the 5th clutch drum (B)
in the direction shown. Starting with the 5th clutch
flat-plate, alternately install the flat-plates (C) (3)
and discs (D) (3), and alternately install the wave-
plates (E) (2) and discs (D) (2). Install the clutch end-
plate (F) with the flat side down on the top disc.
12. Install the snap ring with a screwdriver to secure
the clutch end-plate.
13. Set a dial indicator (A) on the clutch-end-plate (B).
14. Zero the dial indicator with the clutch end-plate
lifted up to the snap ring (C).
(cont’d)
−
−
−
12
13
−
−
−
−
−
−
−
−
−
−
Clearance between Clutch End-Plate and Top
Disc
Service Limit:
1st Clutch:
1.15
1.35 mm (0.045
0.053 in.)
2nd Clutch: 1.05
1.25 mm (0.041
0.049 in.)
3rd Clutch: 0.8
1.0 mm (0.031
0.039 in.)
4th Clutch: 0.75
0.95 mm (0.030
0.037 in.)
5th Clutch: 0.75
0.95 mm (0.030
0.037 in.)
1ST CLUTCH END-PLATES
Plate
No.
Part Number
Thickness
2ND CLUTCH END-PLATES
Plate
No.
Part Number
Thickness
14-354
Shafts and Clutches
Clutch Clearance Inspection (cont’d)
C
A
E
D
B
07ZAE-PRP0100
15. Release the clutch end-plate to lower the clutch-
end-plate, then put the clutch compressor
attachment on the end-plate (A).
16. Press the special tool down with 150
160 N
(15
16 kgf, 33
35 lbf) (B) using a force gauge, and
read the dial indicator (C).
17. The dial indicator reads the clearance (D) between
the clutch end-plate and top disc (E). Take
measurements in at least three places, and use the
average as the actual clearance.
18. If the clearance is out of the service limit, select a
new clutch-end-plate from the following table.
1
22551-RDK-003
3.1 mm (0.122 in.)
2
22552-RDK-003
3.2 mm (0.126 in.)
3
22553-RDK-003
3.3 mm (0.130 in.)
4
22554-RDK-003
3.4 mm (0.134 in.)
5
22555-RDK-003
3.5 mm (0.138 in.)
6
22556-RDK-003
3.6 mm (0.142 in.)
7
22557-RDK-003
3.7 mm (0.146 in.)
8
22558-RDK-003
3.8 mm (0.150 in.)
9
22559-RDK-003
3.9 mm (0.154 in.)
1
22561-RDK-003
2.1 mm (0.083 in.)
2
22562-RDK-003
2.2 mm (0.087 in.)
3
22563-RDK-003
2.3 mm (0.091 in.)
4
22564-RDK-003
2.4 mm (0.094 in.)
5
22565-RDK-003
2.5 mm (0.098 in.)
6
22566-RDK-003
2.6 mm (0.102 in.)
7
22567-RDK-003
2.7 mm (0.106 in.)
8
22568-RDK-003
2.8 mm (0.110 in.)
9
22569-RDK-003
2.9 mm (0.114 in.)
3RD CLUTCH END-PLATES
Plate
No.
Part Number
Thickness
4TH and 5TH CLUTCH END-PLATES
Plate
No.
Part Number
Thickness
14-355
1
22591-RDK-A01
2.1 mm (0.083 in.)
2
22592-RDK-A01
2.2 mm (0.087 in.)
3
22593-RDK-A01
2.3 mm (0.091 in.)
4
22594-RDK-A01
2.4 mm (0.094 in.)
5
22595-RDK-A01
2.5 mm (0.098 in.)
6
22596-RDK-A01
2.6 mm (0.102 in.)
7
22597-RDK-A01
2.7 mm (0.106 in.)
8
22598-RDK-A01
2.8 mm (0.110 in.)
9
22599-RDK-A01
2.9 mm (0.114 in.)
1
22571-RJB-003
2.1 mm (0.083 in.)
2
22572-RJB-003
2.2 mm (0.087 in.)
3
22573-RJB-003
2.3 mm (0.091 in.)
4
22574-RJB-003
2.4 mm (0.094 in.)
5
22575-RJB-003
2.5 mm (0.098 in.)
6
22576-RJB-003
2.6 mm (0.102 in.)
7
22577-RJB-003
2.7 mm (0.106 in.)
8
22578-RJB-003
2.8 mm (0.110 in.)
9
22579-RJB-003
2.9 mm (0.114 in.)
19. Install the new clutch end-plate, and recheck the
clearance. If the thickest clutch end-plate is
installed, but the clearance is still over the service
limit, replace the clutch discs and plates.
01
02
03
SJC8A00E10411310011LDAT00
Special Tools Required
14-356
Shafts and Clutches
Clutch Reassembly
C
A
B
A
A
C
A
B
C
A
B
A
• Clutch spring compressor attachment
07LAE-PX40100 or 07HAE-PL50101
• Clutch spring compressor bolt assembly
07GAE-PG40200 or 07GAE-PG4020A
1. Soak the clutch discs thoroughly in ATF for a
minimum of 30 minutes.
2. Install the new O-rings (A) on the 1st-hold clutch
piston (B), and install the 1st-hold clutch piston in
the 1st clutch piston (C).
3. Install the new O-rings (A) on the 1st clutch piston
(B), and install the 1st/1st-hold clutch piston in the
1st/1st-hold clutch drum (C) while applying
pressure and rotating to ensure proper seating. Do
not pinch the O-rings.
4. Install the O-rings (A) on the 2nd, 3rd, 4th and 5th
clutch piston (B).
5. Install the clutch pistons in the clutch drums (C)
while applying pressure and rotating to ensure
proper seating. Do not pinch the O-ring.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст