Honda Ridgeline. Manual — part 54
08
09
10
Installation
Specified Torque
8 x 1.25 mm:
22 N·m (2.2 kgf·m, 16 lbf·ft)
Specified Torque
6 x 1.0 mm:
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
9-5
A
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
1. Put a new gasket and the spacer on the injector
base.
2. Install the intake manifold. Tighten the bolts and
nuts sequentially, in two or three steps. Always use
a new intake manifold gasket.
3. Install the upper cover. Tighten the bolts and nuts
sequentially, in two or three steps. Always use a
new gasket.
4. Install the harness clamp bracket (A) and water
bypass hoses (B).
5. Connect the engine wire harness connectors, and
install the wire harness clamps to the intake
manifold.
• Intake air temperature (IAT) sensor connector
• Throttle actuator connector
• Manifold absolute pressure (MAP) sensor
connector
• Evaporative emission (EVAP) canister purge
valve connector
• Intake manifold tuning (IMT) valve actuator
connector
(cont’d)
11
12
13
9-6
Intake Manifold and Exhaust System
Intake Manifold Removal and Installation (cont’d)
A
B
C
B
A
6. Install the positive crankcase ventilation (PCV) hose
(A), brake booster vacuum hose (B), and
evaporative emission (EVAP) canister purge hose
(C).
7. Install the air intake duct (A), then install the
breather pipe (B).
8. Clean up any spilled engine coolant.
9. After installation, check that all tubes, hoses and
connectors are installed correctly.
10. Install the engine cover.
11. Refill the radiator with engine coolant, then bleed
air from the cooling system with the heater valve
open (see step 9 on page 10-7).
*01
SJC8A00A18400025601KBAT00
9-7
Exhaust Pipe and Muffler Replacement
HEAT SHIELD
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
MUFFLER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
GASKET
THREE WAY CATALYTIC
CONVERTER (TWC)
GASKET
TWC TIGHTENING
SELF-LOCKING NUTS
10 x 1.25 mm
33 N·m (3.4 kgf·m, 25 lbf·ft)
SELF-LOCKING NUTS
10 x 1.25 mm
54 N·m (5.5 kgf·m, 40 lbf·ft)
EXHAUST PIPE A
GASKETS
SELF-LOCKING NUT
10 x 1.25 mm
33 N·m (3.4 kgf·m, 25 lbf·ft)
NOTE: Use new gaskets and self-locking nuts when reassembling.
Replace.
Replace.
Torque the bolts in steps.
Replace.
Replace.
Replace.
Replace.
SJC8A000000000J1001ZCAT00
Engine Cooling
Cooling System
Fan Controls
. . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . ..
. . . . . . . . . . . ..
. . . . . . . . . . ..
. . . . . . . . . . . . . . . ..
. . . . . . . . . . . . ..
. . . . . . . . . . ...
. . . . . . . . . ..
. . . . . . . . ..
. . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . ..
. . . . . . . . . . . ..
. . . . . . . . . . ..
. . . . . . . . . . . . . . . ..
. . . . . . . . . . . . ..
. . . . . . . . . . ...
. . . . . . . . . ..
. . . . . . . . ..
Component Location Index
. 10-2
Radiator Cap Test
. 10-3
Radiator Test
. 10-3
Fan Motor Test
. 10-4
Thermostat Test
. 10-4
Water Pump Inspection
. 10-5
Water Pump Replacement
. 10-5
Coolant Check
. 10-6
Coolant Replacement
. 10-6
Thermostat Replacement
. 10-8
Water Passage Replacement
. 10-9
Radiator and Fan Replacement
. 10-12
. . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . . . . .
..
. . . . . . . . . .
. . . . . . . ..
. . . . . . . . . . . . . . .
..
Component Location Index
. 10-15
Symptom Troubleshooting Index
. 10-16
Circuit Diagram
. 10-17
Radiator Fan High Speed Circuit Troubleshooting
. 10-18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст