Honda Ridgeline. Manual — part 144
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-340
EGR System
DTC Troubleshooting (cont’d)
32. Start the engine and let it idle, then connect the
battery negative terminal to EGR valve 6P
connector terminal No. 6 with a jumper wire.
Go to step 51.
Go to step 33.
33. Turn the ignition switch OFF.
34. Remove the EGR valve (see page 11-342).
35. Clean the intake manifold EGR port at the passage
inside the EGR valve with throttle plate and
induction cleaner.
36. Install the EGR valve (see page 11-342).
37. Reconnect all connectors.
38. Turn the ignition switch ON (II).
39. Reset the PCM with the HDS.
40. Do the PCM idle learn procedure (see page 11-273).
41. Do the EGR TEST in the INSPECTION MENU with
the HDS.
Go to step 49.
Go to step 42.
42. Turn the ignition switch OFF.
43. Replace the EGR valve (see page 11-342).
44. Reconnect all connectors.
45. Turn the ignition switch ON (II).
46. Reset the PCM with the HDS.
47. Do the PCM idle learn procedure (see page 11-273).
48. Do the EGR TEST in the INSPECTION MENU with
the HDS.
49. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EGR valve and the PCM, then go to
step 1.
Go to step 50.
50. Monitor the OBD STATUS for DTC P2413 in the
DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 49,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the EGR valve
and the PCM, then go to step 1. If the screen
indicates EXECUTING or OUT OF CONDITION,
keep idling until a result comes on.
Does the engine stall or r un r ough?
Is the r esult OK ?
Is DT C P2413 indicated?
Does the scr een indicate PASSED?
−
−
−
−
YES
NO
YES
NO
11-341
51. Turn the ignition switch OFF.
52. Reconnect all connectors.
53. Update the PCM if it does not have the latest
software (see page 11-7), or substitute a known-
good PCM (see page 11-8).
54. Do the EGR TEST in the INSPECTION MENU with
the HDS.
55. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EGR valve and the PCM. If the PCM
was updated, substitute a known-good PCM
(see page 11-8), then recheck. If the PCM was
substituted, go to step 1.
Go to step 56.
56. Monitor the OBD STATUS for DTC P2413 in the
DTCs MENU with the HDS.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-205). If any other
Temporary DTCs or DTCs were indicated in step 51,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the EGR valve
and the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-8), then recheck. If
the PCM was substituted, go to step 1. If the screen
indicates EXECUTING or OUT OF CONDITION,
keep idling until a result comes on.
Is DT C P2413 indicated?
Does the scr een indicate PASSED?
01
SJC8A00A20323525401KBAT00
11-342
EGR System
EGR Valve Replacement
A
B
C
22 N·m
(2.2 kgf·m,
16 lbf·ft)
1. Remove the intake manifold cover (see step 1 on
page 9-3).
2. Disconnect the EGR valve 6P connector (A).
3. Remove the EGR valve (B).
4. Install the parts in the reverse order of removal
with a new gasket (C).
5. Install the intake manifold cover (see step 10 on
page 9-6).
*01
SJC8A00A20360300000DAAT00
11-343
PCV System
Component Location Index
POWERTRAIN CONTROL MODULE (PCM)
PCV VALVE
Update, page 11-7
Substitution, page 11-8
Replacement, page 11-205
Inspection, page 11-345
Replacement, page 11-345
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст