Honda CR-V Hybrid (2022 year). Manual in english — page 40
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
640
Han
d
lin
g the U
n
expected
You can use the kit to inflate a non-punctured under-inflated tire.
1.
Open the trunk floor lid.
2
Getting Ready to Temporarily Repair
the Flat Tire
P. 630
2.
Remove the kit from the case.
3.
Place the kit, face up, on flat ground near
the tire to be inflated, away from traffic.
Do not place the kit on its side.
4.
Remove the sealant/air hose from the kit.
5.
Remove the valve cap.
6.
Attach the sealant/air hose onto the tire
valve stem. Screw it clockwise until it is
tight.
■
Inflating an Under-inflated Tire
1
Inflating an Under-inflated Tire
NOTICE
Do not operate the temporary tire repair kit
compressor for more than 15 minutes. The
compressor can overheat and become permanently
damaged.
Sealant/Air
Hose
Valve Cap
Tire Valve Stem
Sealant/Air Hose
Continued
641
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
Han
d
lin
g the U
n
expected
7.
Plug in the kit to the accessory power
socket.
u
Be careful not to pinch the cord in a
door or window.
2
8.
Turn on the vehicle’s power system.
2
u
Keep the power system on while
injecting sealant and air.
2
9.
Turn the selector knob to
AIR
.
10.
Press the inflator switch to turn on the kit.
u
The compressor starts to inject air into
the tire.
11.
Inflate the tire to the specified air pressure.
1
Inflating an Under-inflated Tire
3
WARNING
Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid buildup of toxic carbon
monoxide.
Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.
AIR
Side
ON
642
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
Han
d
lin
g the U
n
expected
12.
Turn off the kit.
u
Check the pressure gauge on the air
compressor.
u
If overinflated, press the pressure relief
button.
13.
Unplug the kit from the accessory power
socket.
14.
Unscrew the sealant/air hose from the tire
valve stem. Reinstall the valve cap.
15.
Press the pressure relief button until the
gauge returns to 0 psi (0 kPa).
16.
Repackage and properly stow the kit.
Pressure Relief Button
643
Han
d
lin
g the U
n
expected
Handling of the Jack
Your vehicle has jacking points as shown.
When replacing your tires, consult a dealer.
Jacking Points
644
Han
d
lin
g the U
n
expected
Power System Won’t Start
Checking the Procedure
When the
READY
indicator does not come on and the
Ready To Drive
message
does not appear on the driver information interface, check the following items and
take appropriate action.
Checklist
Condition
What to Do
Check if the related
indicator or driver
information interface
messages come on.
The
Temperature Is Too Cold For Vehicle To Operate
message appears.
2
Driver Information Interface Warning and
Information Messages
P. 109
The
To Start, Hold Remote Near Start Button
message
appears.
u
Make sure the keyless remote is in its operating range.
2
P. 186
2
If the Keyless Remote Battery is Weak
P. 645
The
POWER SYSTEM
indicator comes on.
Have your vehicle checked by a dealer.
The transmission system indicator blinks and
Transmission
Problem. Apply Parking Brake When Parked
message
appears.
2
If the Transmission System Indicator Blinks
along with the Warning Message
Check the brightness
of the interior lights.
The interior lights are dim or do not come on at all.
Have the 12-volt battery checked by a dealer.
The interior lights come on normally.
Check all fuses, or have your vehicle checked by
a dealer.
2
Check the shift
position.
The transmission is not in
(
P
.
Put the transmission into
(
P
.
Check the
immobilizer system
indicator.
When the immobilizer system indicator is blinking, the power
system cannot be turned on.
2
1
If you must start the vehicle immediately, use an
assisting vehicle or booster battery to jump start it.
2
If the 12-Volt Battery Is Dead
P. 647
645
uu
Power System Won’t Start
u
If the Keyless Remote Battery is Weak
Han
d
lin
g the U
n
expected
If the Keyless Remote Battery is Weak
If the beeper sounds, the
To Start, Hold Remote Near Start Button
message
appears on the driver information interface, the
POWER
button flashes, and the
READY
indicator does not come on, turn on the power system as follows:
1.
Touch the center of the
POWER
button
with the
H
logo on the keyless remote while
the
POWER
button is flashing. The buttons
on the keyless remote should be facing you.
u
The
POWER
button flashes for about 30
seconds.
2.
Depress the brake pedal and press the
POWER
button within 10 seconds after the
beeper sounds and the
POWER
button
changes from flashing to on.
u
The
READY
indicator comes on.
u
If you don’t depress the pedal, the mode
will change to ACCESSORY.
646
uu
Power System Won’t Start
u
Emergency Power System Off
Han
d
lin
g the U
n
expected
Emergency Power System Off
The
POWER
button may be used to turn the power system off due to an emergency
situation even while driving. If you must turn the power system off, do either of the
following operations:
•
Press and hold the
POWER
button for about two seconds.
•
Firmly press the
POWER
button three times.
The steering wheel will not lock. However, because turning off the power system
disables the power assist the power system provides to the steering and braking
systems, it will require significantly more physical effort and time to steer and slow
the vehicle. Use both feet on the brake pedal to slow down the vehicle and stop
immediately in a safe place.
The transmission automatically changes to
(
P
after the vehicle comes to a complete
stop. Then, the power mode changes to VEHICLE OFF.
1
Do not press the
POWER
button while driving unless
it is absolutely necessary for the power system to be
turned off.
If you press the
POWER
button while driving, the
beeper sounds.
647
Continued
Han
d
lin
g the U
n
expected
If the 12-Volt Battery Is Dead
Jump Starting Procedure
Turn off the power to electric devices, such as audio and lights. Turn off the power
system, then open the hood.
1.
Open the terminal cover on your vehicle’s
12-volt battery positive
+
terminal.
2.
Connect the first jumper cable to your
vehicle's 12-volt battery
+
terminal.
3.
Connect the other end of the first jumper
cable to the booster battery
+
terminal.
u
Use a 12-volt booster battery only.
u
When using an automotive battery charger
to boost your 12-volt battery, select a
lower charging voltage than 15-volt. Check
the charger manual for the proper setting.
1
Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Be careful
not to tangle the jumper cables or allow the cable
ends to touch each other while attaching or
detaching the jumper cables.
12-volt battery performance degrades in cold
conditions and may prevent the engine from starting.
3
WARNING
A 12-volt battery can explode if you do not
follow the correct procedure, seriously
injuring anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the 12-volt battery.
+
Terminal
Models without Fuse Box Type C
+
Terminal
Models with Fuse Box Type C
Booster Battery
uu
If the 12-Volt Battery Is Dead
u
Jump Starting Procedure
648
Han
d
lin
g the U
n
expected
4.
Connect the second jumper cable to the
booster battery
-
terminal.
5.
Connect the other end of the second
jumper cable to the engine mounting bolt
as shown. Do not connect this jumper cable
to any other part.
6.
If your vehicle is connected to another
vehicle, start the assisting vehicle's engine
and increase its rpm slightly.
7.
Attempt to start your vehicle's engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Once your vehicle's engine has started, remove the jumper cables in the following
order.
1.
Disconnect the jumper cable from your vehicle's ground.
2.
Disconnect the other end of the jumper cable from the booster battery
-
terminal.
3.
Disconnect the jumper cable from your vehicle's 12-volt battery
+
terminal.
4.
Disconnect the other end of the jumper cable from the booster battery
+
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
■
What to Do After the Engine Starts
1
The indicators for the Adaptive Cruise Control (ACC)
with Low Speed Follow, Road Departure Mitigation,
Vehicle Stability Assist
TM
(VSA
®
) system, Vehicle
Stability Assist
TM
(VSA
®
) OFF, Collision Mitigation
Braking System
TM
(CMBS
TM
), low tire pressure/TPMS,
and Parking Brake and Brake System (Amber) may
come on along with a message in the Driver
Information Interface when you set the power mode
to ON after reconnecting the 12-volt battery.
Drive a short distance at more than 12 mph (20 km/
h). Each indicator should go off. If any do not, have
your vehicle checked by a dealer.
649
Continued
Han
d
lin
g the U
n
expected
Overheating
How to Handle Overheating
Overheating symptoms are as follows:
•
The
High Temperature. Power Reduced.
message appears on the driver
information interface.
•
The
Stop Driving When Safe. Engine Temperature Too Hot
message appears
on the driver information interface.
•
Steam or spray comes out of the engine compartment.
The
High Temperature. Power Reduced.
message appears on the driver
information interface when the power system temperature is high.
2
Driver Information Interface Warning and Information Messages
1.
Immediately park the vehicle in a safe place.
u
Set the parking brake, and put the transmission into
(
P
. Turn off all accessories
and turn on the hazard warning lights.
2.
Keep the power mode in ON, and wait until the message disappears.
u
If the message does not disappear, have your vehicle inspected at a dealer.
■
The High Temperature. Power Reduced. Message Appears
on the Driver Information Interface
uu
Overheating
u
How to Handle Overheating
650
Han
d
lin
g the U
n
expected
■
First thing to do
1.
Immediately park the vehicle in a safe place.
2.
Turn off all accessories and turn on the hazard warning lights.
u
No steam or spray present:
Keep the power system on and open the hood.
u
Steam or spray is present:
Turn off the power system and wait until it
subsides. Then, open the hood.
■
The Stop Driving When Safe. Engine Temperature Too Hot
Message Appears on the Driver Information Interface
1
NOTICE
Continuing to drive with the
Stop Driving When
Safe. Engine Temperature Too Hot
message on
the driver information interface may damage the
engine.
3
WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood if steam is coming
out.
651
uu
Overheating
u
How to Handle Overheating
Han
d
lin
g the U
n
expected
■
Next thing to do
1.
Check that the cooling fan is operating and
turn the power system off once the
Stop
Driving When Safe. Engine
Temperature Too Hot
message on the
driver information interface disappears.
u
If the cooling fan is not operating,
immediately turn the power system off.
2.
Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks.
u
If the coolant level in the engine coolant
reserve tank is low, add coolant until it
reaches the
MAX
mark.
u
If there is no coolant in the engine
coolant reserve tank, check that the
radiator is cool. Cover the radiator cap
with a heavy cloth and open the cap. If
necessary, add coolant up to the base of
the filler neck, and put the cap back on.
■
Last thing to do
Once the engine has cooled sufficiently, turn the power system on.
If the
Stop Driving When Safe. Engine Temperature Too Hot
message does not
appear, resume driving. If it appears again, contact a dealer for repairs.
1
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only.
Have a dealer flush the system with proper antifreeze
as soon as possible.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Engine Coolant Reserve Tank
MAX
MIN
652
Han
d
lin
g the U
n
expected
Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the engine oil pressure is low.
■
What to do as soon as the indicator comes on
1.
Immediately park the vehicle on level ground in a safe place.
2.
If necessary, turn the hazard warning lights on.
■
What to do after parking the vehicle
1.
Turn the power system off and let the engine sit for approximately
three minutes.
2.
Open the hood and check the oil level.
u
Add oil as necessary.
2
3.
Start the engine and check the low oil pressure indicator.
u
The indicator goes off: Start driving again.
u
The indicator does not go off within 10 seconds: Immediately turn
the power system off and contact a dealer for repairs.
If the 12-volt Battery Charging System Indicator
Comes On
■
Reasons for the indicator to come on
Comes on when there is a problem with the charging system.
■
What to do when the indicator comes on
Turn off the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
1
If the Low Oil Pressure Indicator Comes On
NOTICE
Running the engine with low oil pressure can cause
serious mechanical damage almost immediately.
1
If the 12-volt Battery Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
power system. The power system uses the 12-volt
battery to activate. You may not be able to turn the
power system on again if you have turned it off with
this indicator on.
This indicator may come on when the outside
temperature is below -40°F (-40°C). It will go off after
the battery warms up.
653
uu
Indicator, Coming On/Blinking
u
If the Malfunction Indicator Lamp Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Malfunction Indicator Lamp Comes On or
Blinks
■
Reasons for the indicator lamp to come on or blink
•
Comes on when there is a problem with the engine emissions control
system.
•
Blinks when engine misfiring is detected.
■
What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at a
dealer.
■
What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the engine stopped until it cools.
1
If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE
If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer at
31 mph (50 km/h) or less. Have your vehicle
inspected.
654
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On or
Blinks
■
Reasons for the indicator to come on
•
The brake fluid is low.
•
There is a malfunction in the brake system.
■
What to do when the indicator comes on while driving
Depress the brake pedal lightly to check pedal pressure.
•
If normal, check the brake fluid level the next time you stop.
•
If abnormal, take immediate action. If necessary, use the deceleration
paddle selector to slow the vehicle using regenerative braking.
■
Reasons for the indicator to blink
•
There is a problem with the electric parking brake system.
■
What to do when the indicator blinks
Avoid using the parking brake and have your vehicle checked by a dealer
immediately.
1
If the Brake System Indicator (Red) Comes On or Blinks
Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If there
is no resistance from the brake pedal, stop
immediately in a safe place. If necessary use the
deceleration paddle selector to slower your vehicle’s
speed.
If the brake system indicator (red) and
ABS
indicator
come on simultaneously, the electronic brake
distribution system is not working. This can result in
vehicle instability under sudden braking.
Have your vehicle inspected by a dealer immediately.
If the brake system indicator (red) blinks at the same
time when the brake system indicator (amber) comes
on, the parking brake may not work.
Avoid using the parking brake and have your vehicle
checked by a dealer immediately.
2
P. 655
655
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On or Blinks at the
Same Time When the Brake System Indicator (Amber) Comes On
■
If the brake system indicator (red) comes on or blinks at the
same time when the brake system indicator (amber) comes on,
release the parking brake manually or automatically
2
•
If the brake system indicator (red) continuously comes on or blinks at
the same time when the brake system indicator (amber) comes on,
stop the vehicle in a safe place and have it inspected by a dealer
immediately.
u
Preventing the vehicle from moving, put the transmission into
(
P
.
•
If only the brake system indicator (red) is turned off, avoid using the
parking brake and have your vehicle checked by a dealer immediately.
1
If you apply the parking brake, you may not be able
to release it.
If the brake system indicator (red) and the brake
system indicator (amber) come on at the same time,
the parking brake is working.
If the brake system indicator (red) blinks at the same
time when the brake system indicator (amber) comes
on, the parking brake may not work because it is
checking the system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст