Honda Odyssey (2023 year). Manual in english — page 12
uu
Operating the Switches Around the Steering Wheel
u
ENGINE START/STOP Button
190
Co
ntrols
If you open the driver’s door when the power mode is set to ACCESSORY, a warning
beep sound.
When the power mode is set to any mode
other than OFF and you remove the keyless
remote from the vehicle and shut the door, an
alarm will sound. If the alarm continues to
sound, place the keyless remote in another
location.
■
When the power mode is in
ACCESSORY
The alarm will sound from outside the vehicle.
■
When the power mode is in ON
An alarm will sound both inside and outside
the vehicle. In addition, a warning indicator
will appear on the instrument panel.
■
Power Mode Reminder
■
Keyless Remote Reminder
1
When the keyless remote is within the system’s
operational range, and all the doors are closed, the
warning function cancels.
If the keyless remote is taken out of the vehicle after
the engine has been started, you can no longer
change the
ENGINE START/STOP
button mode or
restart the engine. Always make sure if the keyless
remote is in your vehicle when you operate the
ENGINE START/STOP
button.
Removing the keyless remote from the vehicle
through a window does not activate the warning
buzzer.
Do not put the keyless remote on the dashboard or in
the glove box. It may cause the warning buzzer to
activate. Under some other conditions that can
prevent the vehicle from locating the keyless remote,
the warning buzzer may also activate even if the
remote is within the system’s operational range.
191
uu
Operating the Switches Around the Steering Wheel
u
Turn Signals
Co
ntrols
Turn Signals
The turn signals can be used when the power
mode is in ON.
■
(A): Turn signal
Push the lever up or down based on the
direction you want to turn, and the turn signal
will blink.
■
(B): One-touch turn signal
When you lightly push the lever up or down
and release it, the turn signal will blink 3
times.
1
The turn signal indicator on the instrument panel will
blink when the external turn signal blinks.
2
P. 88
(A)
(B)
(B)
(A)
192
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Co
ntrols
Light Switches
Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.
■
High beams
Push the lever forward until you hear a click.
■
Low beams
When in high beams, pull the lever back to
return to low beams.
■
Flashing the high beams
Pull the lever back, and release it.
■
Lights off
Rotate the switch to
OFF
either when:
•
The transmission is in
(
P
.
•
The parking brake is applied.
To turn the lights on again, rotate the switch
to
OFF
to cancel the lights off mode. Even if
you do not cancel the lights off mode, the
lights come on automatically when:
•
The transmission is taken out of
(
P
and the
parking brake is released.
•
The vehicle starts to move.
■
Manual Operation
1
If you leave the power mode in VEHICLE OFF with the
lights on, a chime sounds when the driver’s door is
opened.
When the lights are on, the lights on indicator in the
instrument panel will be on.
2
P. 98
Do not leave the lights on when the engine is off
because it will cause the battery to discharge.
If you sense that the level of the headlights is
abnormal, have the vehicle inspected by a dealer.
High Beams
Flashing the high beams
Low Beams
Models without default AUTO position
switch
Models with default AUTO position
switch
High Beams
Flashing the high beams
Low Beams
Turns on parking, side marker,
tail, and rear license plate lights
Turns on headlights, parking,
side marker, tail, and rear license
plate lights
Models with default AUTO position switch
Continued
193
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
Co
ntrols
Automatic lighting control can be used when
the power mode is in ON.
When you turn the light switch to
AUTO
, the
headlights and other exterior lights will switch
on and off automatically depending on the
ambient brightness.
When the light switch is in
AUTO
, the
headlights and other exterior lights will switch
on and off automatically depending on the
ambient brightness.
The headlights come on when you unlock a
door in dark areas with the headlight switch in
AUTO
.
u
Once you lock the door, the headlights
will go off.
■
Automatic Operation (automatic lighting control)
1
Automatic Operation (automatic lighting control)
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark areas
such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.
Light
Sensor
Models without
automatic
intermittent wiper
Light Sensor
Models with automatic intermittent
wiper
Models without default AUTO position
switch
Models with default AUTO position
switch
Models without default AUTO position switch
Models with default AUTO position switch
uu
Operating the Switches Around the Steering Wheel
u
Light Switches
194
Co
ntrols
The headlights automatically come on when the wipers are used several times within
a certain number of intervals with the headlight switch in
AUTO
.
The headlights automatically go off a few minutes later if the wipers are stopped.
The headlights, all other exterior lights, and the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF, take the remote with you,
and close the driver’s door.
If you set the power mode to VEHICLE OFF with the headlight switch on, but do not
open the door, the lights turn off after 10 minutes (3 minutes, if the switch is in the
AUTO
position).
The lights turn on again when you unlock or open the driver’s door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver’s door, you will hear a reminder chime alerting you that the lights are on.
■
Headlight Integration with Wiper
■
Automatic Lighting Off Feature
1
Automatic Operation (automatic lighting control)
You can adjust the auto light sensitivity as follows:
2
P. 413
Setting
The exterior lights come on
when the ambient light is at
MAX
HIGH
MID
LOW
MIN
U.S. models
Bright
Dark
1
Headlight Integration with Wiper
This feature activates when
AUTO
mode is selected
and the headlights are off.
The instrument panel brightness does not change
when the headlights come on.
At dark ambient light levels, the automatic lighting
control feature turns on the headlights, regardless of
the number of wiper sweeps.
1
Automatic Lighting Off Feature
You can change the headlight auto off timer setting.
2
P. 413
195
uu
Operating the Switches Around the Steering Wheel
u
Fog Lights
Co
ntrols
Fog Lights
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.
Fog Light Switch
196
uu
Operating the Switches Around the Steering Wheel
u
Daytime Running Lights
Co
ntrols
Daytime Running Lights
When the conditions listed below are met, the daytime running lights come on:
•
The power mode is in ON.
•
The headlight switch is off.
•
The parking brake is released.
The lights remain on even if you set the parking brake. Setting the power mode to
VEHICLE OFF will turn off the daytime running lights.
The daytime running lights go off once the headlight switch is turned on, or when
the headlight switch is in
AUTO
and it is getting dark outside.
197
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
Continued
Co
ntrols
Auto High-Beam
The front sensor camera detects the light sources ahead of the vehicle such as the
lights of a preceding or oncoming vehicle, or street lights. When you are driving at
night, the system automatically switches the headlights between low beam and high
beam depending on the situation.
When all of the following conditions have been met, the auto high-beam indicator
comes on and the auto high-beam is activated.
•
The power mode is in ON.
•
The light switch is in
AUTO
.
•
The lever is in the low beam position.
•
The headlights have been automatically
activated.
•
It is dark outside the vehicle.
If the auto high-beam indicator does not come on even when all the conditions have
been met, carry out the following procedure and the indicator will come on.
•
Pull the lever toward you for flashing the high beams then release it while driving.
1
The auto high-beam system does not always operate
in every situation. This system is just for assisting the
driver. Always observe your surroundings and switch
the headlights between high beam and low beam
manually if necessary.
If you find the timing of beam changes inconvenient
for driving, change the headlight beams manually.
The range and the distance at which the camera can
recognize varies depending on conditions
surrounding your vehicle.
Regarding the handling of the camera mounted to
the inside of the windshield, refer to the following.
2
P. 558
For the auto high-beam to work properly:
•
Do not place an object that reflects light on the
dashboard.
•
Keep the windshield around the camera clean.
When cleaning the windshield, be careful not to
apply the windshield cleanser to the camera lens.
•
Do not attach an object, sticker or film to the area
around the camera.
•
Do not touch the camera lens.
If the camera receives a strong impact, or repairing of
the area near the camera is required, consult a dealer.
■
How to Use the Auto High-Beam
Front Sensor Camera
Light Switch
Auto High-
Beam
Indicator
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
198
Co
ntrols
■
Automatic switching between high-beam and low-beam
When auto-high beam is active, the headlights switch between high beam and low
beam based on the following conditions.
■
Manual switching between high-beam and low-beam
If you want to manually switch the headlights between high beam and low beam,
follow either of the procedures below. Note that when you do this, the auto high-
beam indicator will turn off and the auto high-beam will be deactivated.
Using the lever:
Pull the lever toward you for flashing the high beams then release it within about
one second while driving.
u
To reactivate the auto high-beam, pull the lever toward you for flashing the
high beams then release it while driving. The auto high-beam indicator will
come on.
Using the light switch:
Turn the light switch to
.
u
To reactivate the auto high-beam, turn the light switch to
AUTO
when the
lever is in the low beam position, the auto high-beam indicator will come on.
1
In the following cases, the auto high-beam system
may not switch the headlights properly or the
switching timing may be changed. In case of the
automatic switching operation does not fit for your
driving habits, please switch the headlights manually.
•
The brightness of the lights from the preceding or
oncoming vehicle is intense or poor.
•
Visibility is poor due to the weather (rain, snow,
fog, windshield frost, etc.).
•
Surrounding light sources, such as street lights,
electric billboards and traffic lights are illuminating
the road ahead.
•
The brightness level of the road ahead constantly
changes.
•
The road is bumpy or has many curves.
•
A vehicle suddenly appears in front of you, or a
vehicle in front of you is not in the preceding or
oncoming direction.
•
Your vehicle is tilted with a heavy load in the rear.
•
A traffic sign, mirror, or other reflective object
ahead is reflecting strong light toward the vehicle.
•
The oncoming vehicle frequently disappears under
roadside trees or behind median barriers.
•
The preceding or oncoming vehicle is a motorcycle,
bicycle, mobility scooter, or other small vehicle.
The auto high-beam system keeps the headlight low
beam when:
•
Windshield wipers are operating at a high speed.
•
The camera has detected dense fog.
Switching to high beam:
All of the following conditions must
be met before the high beams turn
on.
•
Your vehicle speed is 25 mph (40
km/h) or more.
•
There are no preceding or
oncoming vehicle with headlights
or taillights turned on.
•
There are few street lights on the
road ahead.
Switching to low beam:
One of the following conditions
must be met before the low beams
turn on.
•
Your vehicle speed is 15 mph (24
km/h) or less.
•
There is a preceding or oncoming
vehicle with headlights or
taillights turned on.
•
There are many street lights on
the road ahead.
199
uu
Operating the Switches Around the Steering Wheel
u
Auto High-Beam
Co
ntrols
You can turn the auto high-beam system off. If you want to turn the system off or
on, set the power mode to ON, then carry out the following procedures while the
vehicle is stationary.
To turn the system off:
With the light switch is in
AUTO
, pull the lever
toward you and hold it for at least 40 seconds.
After the auto high-beam indicator light blinks
twice, release the lever.
To turn the system on:
With the light switch is in
AUTO
, pull the lever
toward you and hold it for at least 30 seconds.
After the auto high-beam indicator light blinks
once, release the lever.
■
How to Turn Off the Auto High-Beam
1
If the
Some Driver Assist Systems Cannot
Operate: Camera Temperature Too High
message
appears:
•
Use the climate control system to cool down the
interior and, if necessary, also use defroster mode
with the airflow directed toward the camera.
•
Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the camera.
If the
Some Driver Assist Systems Cannot
Operate: Clean Front Windshield
message
appears:
•
Park your vehicle in a safe place, and clean the
windshield. If the message does not disappear after
you have cleaned the windshield and driven for a
while, have your vehicle checked by a dealer.
1
How to Turn Off the Auto High-Beam
If you turn the auto high-beam system off, the system
does not operate until you turn the system on.
Park in a safe place before turning the system off or
on.
AUTO
Position
200
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
Wipers and Washers
The windshield wipers and washers can be
used when the power mode is in ON.
■
MIST
The wipers run at high speed until you release
the lever.
■
Wiper switch (OFF, INT
*1
/AUTO
*2
, LO,
HI)
Move the lever up or down to change the
wiper settings.
■
Adjusting wiper operation
*
Turn the adjustment ring to adjust wiper
operation.
■
Washer
Sprays while you pull the lever toward you.
When you release the lever for more than one
second, the spray stops, the wipers sweep two
or three more times to clear the windshield,
then stop.
*1: Models with manual intermittent operation
*2: Models with automatic intermittent operation
■
Windshield Wiper/Washer
1
NOTICE
Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged.
NOTICE
In cold weather, the blades may freeze to the
windshield.
Operating the wipers in this condition may damage
the wipers. Use the defroster or heated windshield
*
to warm the windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens.
When the vehicle speeds up, the wiper operation’s
shortest delay setting ( ) and the
LO
setting become
the same.
NOTICE
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
Models with intermittent time adjustment ring
Intermittent Time
Adjustment Ring
*
MIST
INT
*1
/
AUTO
*2
OFF
LO
: Low speed wipe
HI
: High speed wipe
Pull to
use
washer.
Lower speed, fewer sweeps
Higher speed, more sweeps
* Not available on all models
Continued
201
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
When you push the lever down to
AUTO
, the
windshield wipers sweep once, and go into
the automatic mode.
The wipers operate intermittently, at low
speed, or at high speed and stop in
accordance with the amount of rainfall the
rainfall sensor detects.
■
AUTO sensitivity adjustment
When the wiper function is set to
AUTO
, you
can adjust the sensitivity of the rainfall sensor
(using the adjustment ring) so that wipers will
operate in accordance with your preference.
Sensor sensitivity
■
Automatic Intermittent Wipers
*
1
If the wipers stop operating due to any obstacle such
as the buildup of snow, park the vehicle in a safe
place.
Rotate the wiper switch to OFF, and set the power
mode to ACCESSORY or VEHICLE OFF, then remove
the obstacle.
The wiper motor may stop motor operation
temporarily to prevent an overload. Wiper operation
will return to normal within a few minutes.
1
The rainfall sensor is in the location shown below.
NOTICE
AUTO
should always be turned
OFF
before the
following situation in order to prevent severe damage
to the wiper system:
•
Cleaning the windshield
•
Driving through a car wash
•
No rain present
Rainfall Sensor
Adjustment Ring
Low Sensitivity
High Sensitivity
* Not available on all models
202
uu
Operating the Switches Around the Steering Wheel
u
Wipers and Washers
Co
ntrols
The rear wiper and washer can be used when
the power mode is in ON.
■
Wiper switch (OFF, INT, ON)
Change the wiper switch setting according to
the amount of rain.
■
Washer (
)
Sprays while you rotate the switch to this
position.
Hold it to activate the wiper and to spray the
washer. Once released, the washer spray will
stop and the rear wiper will return to its
selected switch setting after a few sweeps.
■
Operating in reverse
When you put the transmission into
(
R
with the windshield wiper activated, the rear
wiper operates automatically as follows even if its switch is off.
*1: Models with manual intermittent operation
*2: Models with automatic intermittent operation
■
Rear Wiper/Washer
ON
: Continuous wipe
Washer
OFF
INT
: Intermittent
Front Wiper Position
Rear Wiper Operation
INT
*1
(Intermittent)
AUTO
*2
(Intermittent)
Intermittent
LO
(Low speed wipe)
HI
(High speed wipe)
Continuous
203
uu
Operating the Switches Around the Steering Wheel
u
Rear Defogger/Heated Door Mirror Button
Co
ntrols
Rear Defogger/Heated Door Mirror Button
Press the rear defogger and heated door
mirror button to defog the rear window and
mirrors when the power mode is in ON.
The rear defogger and heated door mirrors
automatically switch off after 10-30 minutes
depending on the outside temperature.
However, if the outside temperature is 32°F
(0°C) or below, they do not automatically
switch off.
1
Rear Defogger/Heated Door Mirror Button
This system consumes a lot of power, so turn it off
when the window has been defogged.
Also, do not use the system for a long time while the
engine is idling. This may weaken the battery, making
it difficult to start the engine.
When the power mode is set to ON and the outside
temperature is below 41°F (5°C), the heated door
mirror may automatically activate for 10 minutes.
204
uu
Operating the Switches Around the Steering Wheel
u
Heated Windshield Button
Co
ntrols
Heated Windshield Button
Press the heated windshield button to deice
the windshield when the power mode is in
ON.
Canadian models
1
This system consumes a lot of power, so turn it off
when the window has been deiced. Also, do not use
the system for a long period when the engine is
idling. This may weaken the battery, making it
difficult to start the engine.
When the outside temperature is below 39°F (4°C),
the heated windshield may automatically activate.
The system deactivates itself once the outside
temperature reaches 43°F (6°C).
205
uu
Operating the Switches Around the Steering Wheel
u
Brightness Control
Co
ntrols
Brightness Control
When the power mode is in ON, you can use
the brightness control knob to adjust
instrument panel brightness.
Brighten:
Turn the knob to the right.
Dim:
Turn the knob to the left.
You will hear a beeper when the brightness
reaches minimum or maximum. Several
seconds after you have adjusted the
brightness, you will be returned to the
previous screen.
■
Brightness level indicator
The brightness level is shown on the driver
information interface while you are adjusting
it.
1
The brightness of the instrument panel will be
reduced when the following conditions have been
met:
•
The power mode is in ON.
•
The parking lights are turned on.
•
The ambient lighting is low.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
Control Knob
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст