Honda Element. Manual — part 235

14. Drive the vehicle in 4th or 5th gear in the D position, then shift to the 2 position. The vehicle should

immediately begin to slow down from engine braking.

15. Shift to the 1 position, accelerate from a stop at full throttle, and check for abnormal noise and clutch

slippage. Upshifts should not occur in this position.

16. Shift to the 2 position, accelerate from a stop at full throttle, and check for abnormal noise and clutch

slippage. Upshifts and downshifts should not occur in this position.

17. Shift to the R position, accelerate from a stop at full throttle momentarily, and check for abnormal noise

and clutch slippage.

18. Park the vehicle on a slope (about 16 degrees), apply the brake, and shift into the P position. Release the

brake; the vehicle should not move.

STALL SPEED TEST

1. Make sure the transmission fluid is filled to the proper level (see ATF LEVEL CHECK ).

2. Apply the parking brake, and block all four wheels.

3. Connect the HDS to the DLC (A), and go to the A/T data list. If the HDS does not communicate with the

PCM, troubleshoot the DLC circuit (see DLC CIRCUIT TROUBLESHOOTING ).

Fig. 169: Identifying Data Link Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.

4. Make sure the A/C switch is OFF.

5. After the engine has warmed up to normal operating temperature (the radiator fan comes on), shift to the

2 position.

6. Firmly press the brake pedal, then fully press the accelerator pedal for 6 to 8 seconds, and note the engine

2nd-->1st

26-31 mph (42-50 km/h)

NOTE:

Always use the parking brake to hold the vehicle, when stopped on an
incline in gear. Depending on the grade of the incline, the vehicle could
roll if the brake is released.

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

speed. Do not move the shift lever while raising engine speed.

7. Allow 2 minutes for cooling, then repeat the test in the D, 1, and R positions.

Stall Speed rpm:

Specification: 2,400 rpm

Service Limit: 2,250-2,550 rpm

8. If the measurements are out of the service limit, problems and probable causes are listed in the table.

SYMPTOM PROBLEM CHART

PRESSURE TEST

Special Tools Required



A/T oil pressure gauge set w/panel 07406-0020400 or 07406-0020401



A/T pressure hose, 2,210 mm 07MAJ-PY4011A



A/T pressure hose adapter 07MAJ-PY40120

1. Make sure the transmission fluid is filled to the proper level (see ATF LEVEL CHECK ).

2. 4WD: Raise the vehicle on a lift, make sure it is securely supported, and allow all four wheels to rotate

freely.

NOTE:



Do not test stall speed for more than 10 seconds at a time.



Stall speed tests should be used for diagnostic purposes only.



Stall speed tests should be the same in D, 2,1, and R positions.



Do not test stall speed with the A/T oil pressure gauges installed.

Problem

Probable causes

Stall speed rpm high in the D, 2,1, and R positions



ATF pump output low



Clogged ATF strainer



Regulator valve stuck



Slipping clutch

Stall speed rpm high in the 1 position

Slippage of 1st clutch

Stall speed rpm high in the 2 position

Slippage of 2nd clutch

Stall speed rpm high in the R position

Slippage of 4th clutch

Stall speed rpm low in the D, 2,1, and R positions



Engine output low



Engine throttle valve closed



Torque converter one-way clutch slipping

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

2WD: Raise the front of the vehicle, make sure it is securely supported. Set the parking brake, block rear
wheels securely, and allow the front wheels to rotate freely. Or raise the vehicle on a lift.

3. Remove the splash shield.

4. Connect the HDS to the DLC (A), and go to the A/T data list. If the HDS does not communicate with the

PCM, troubleshoot the DLC circuit (see DLC CIRCUIT TROUBLESHOOTING ).

Fig. 170: Identifying Data Link Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.

5. Connect the A/T oil pressure gauge to the line pressure inspection port (A). Do not allow dust or other

foreign particles to enter the port while connecting the gauge.

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

Fig. 171: Connecting A/T Oil Pressure Gauge To Line Pressure Inspection Port
Courtesy of AMERICAN HONDA MOTOR CO., INC.

6. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).

7. With the shift lever in the P or N position while holding the engine speed at 2,000 rpm, measure the line

pressure.

FLUID PRESSURE SPECIFICATIONS

8. Turn the engine off, then disconnect the A/T oil pressure gauge from the line pressure inspection port.

9. Install the sealing bolt to the line pressure inspection port with the new sealing washer, and tighten the

bolts to 18 N.m (1.8 kgf.m, 13 lbf.ft). Do not reuse old sealing washer.

10. Connect the A/Toil pressure gauge to the 1st clutch pressure inspection port (B).

NOTE:

Higher pressure may be indicated if measurements are made with shift
lever in a position other than P or N.

Pressure

Fluid Pressure

Standard

Service Limit

Line (A)

900-960 kPa (9.2-9.8 kgf/cm

2

,

130-140 psi)

850 kPa (8.7 kgf/cm

2

, 120 psi)

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element