Honda Element. Manual — part 57
Enable Conditions
ENABLE CONDITIONS
Malfunction Threshold
The return signal does not match the command to turn ON shift solenoid valve A for at least 1 second.
Driving Pattern
Start the engine, and drive the vehicle with the 1st gear in D position for at least 1 second.
Drive the vehicle in this manner only if the traffic regulations and ambient conditions allow.
Diagnosis Details
Conditions for illuminating the MIL
When a malfunction is detected, the MIL comes on and the DTC and the freeze frame data are stored in the
PCM memory.
Conditions for clearing the MIL
The MIL will be cleared if the malfunction does not recur during three consecutive trips in which the diagnostic
runs.
The MIL, the DTC, and the freeze frame data can be cleared by using the scan tool Clear command or by
disconnecting the battery.
DTC P0974 (7): ADVANCED DIAGNOSTICS
DTC P0974: OPEN IN SHIFT SOLENOID VALVE A CIRCUIT
OBD Status
PASSED/FAILED/NOT COMPLETED (STILL TESTING)
Condition
Minimum
Maximum
Battery voltage
11.0 V
-
No active DTCs
P0966, P0967, P0970, P0971, P0974
2007 Honda Element EX
2007 ENGINE PERFORMANCE Advanced Diagnostics - Element
Fig. 163: Shift Solenoid Valve A Circuit Diagram
Fig. 164: Shift Solenoid Valve Driving Signal Combination Table
General Description
When shift solenoid valves A, B, C, D, and E are turned ON, the hydraulic pressure circuit opens. The hydraulic
pressure circuit supplies/discharges hydraulic pressure to/from each clutch according to the combination of the
ON/OFF status of those valves and the shift valves. The powertrain control module (PCM) commands the
driver circuit to turn on the shift solenoid valve. The circuit diagnoses malfunctions such as a circuit short or
open, and sends back a return signal during the PCM's command. When the return signal does not match the
PCM command, a malfunction is detected by the PCM. The malfunction is detected when the return signal does
not match the PCM command to turn OFF the shift solenoid valve, and a DTC is stored.
Monitor Execution, Sequence, Duration, DTC Type, OBD Status
MONITOR DESCRIPTION
Enable Conditions
ENABLE CONDITIONS
Execution
Continuous
Sequence
None
Duration
1 second or more
DTC Type
One drive cycle, MIL ON, D indicator blinks
OBD Status
PASSED/FAILED/NOT COMPLETED (STILL TESTING)
Condition
Minimum
Maximum
Battery voltage
11.0 V
-
No active DTCs
P0966, P0967, P0970, P0971, P0973
2007 Honda Element EX
2007 ENGINE PERFORMANCE Advanced Diagnostics - Element
Malfunction Threshold
The return signal does not match the command to turn OFF shift solenoid valve A for at least 1 second.
Driving Pattern
Start the engine, shift to P position, and wait for at least 1 second.
Drive the vehicle in this manner only if the traffic regulations and ambient conditions allow.
Diagnosis Details
Conditions for illuminating the MIL
When a malfunction is detected, the MIL comes on and the DTC and the freeze frame data are stored in the
PCM memory.
Conditions for clearing the MIL
The MIL will be cleared if the malfunction does not recur during three consecutive trips in which the diagnostic
runs.
The MIL, the DTC, and the freeze frame data can be cleared by using the scan tool Clear command or by
disconnecting the battery.
DTC P0976 (8): ADVANCED DIAGNOSTICS
DTC P0976: SHORT IN SHIFT SOLENOID VALVE B CIRCUIT
Fig. 165: Shift Solenoid Valve B Circuit Diagram
2007 Honda Element EX
2007 ENGINE PERFORMANCE Advanced Diagnostics - Element
Fig. 166: Shift Solenoid Valve Driving Signal Combination Table
General Description
When shift solenoid valves A, B, C, D, and E are turned ON, the hydraulic pressure circuit opens. The hydraulic
pressure circuit supplies/discharges hydraulic pressure to/from each clutch according to the combination of the
ON/OFF status of those valves and the shift valves. The powertrain control module (PCM) commands the
driver circuit to turn on the shift solenoid valve. The circuit diagnoses malfunctions such as a circuit short or
open, and sends back a return signal during the PCM's command. When the return signal does not match the
PCM command, a malfunction is detected by the PCM. The malfunction is detected when the return signal does
not match the PCM command to turn ON the shift solenoid valve, and a DTC is stored.
Monitor Execution, Sequence, Duration, DTC Type, OBD Status
MONITOR DESCRIPTION
Enable Conditions
ENABLE CONDITIONS
Malfunction Threshold
Execution
Continuous
Sequence
None
Duration
1 second or more
DTC Type
One drive cycle, MIL ON, D indicator blinks
OBD Status
PASSED/FAILED/NOT COMPLETED (STILL TESTING)
Condition
Minimum
Maximum
Battery voltage
11.0 V
-
No active DTCs
P0977, P0985, P0986
2007 Honda Element EX
2007 ENGINE PERFORMANCE Advanced Diagnostics - Element
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст