Honda CR-V (2022 year). Manual in english — page 43
687
uu
Maintenance Under the Bonnet
u
Engine Coolant
Main
tenan
ce
•
Never open when hot.
•
Hot coolant will scald you.
•
Relief pressure valve begins to open at 108
kPa.
■
Engine Coolant Reserve Tank Cap
688
uu
Maintenance Under the Bonnet
u
Transmission Fluid
Main
tenan
ce
Transmission Fluid
Have a dealer check the fluid level and replace if necessary.
Follow your vehicle’s maintenance service timing of when to change continuously
variable transmission fluid.
2
Do not attempt to check or change the continuously variable transmission fluid
yourself.
Have a dealer check the fluid level and replace if necessary.
Follow your vehicle’s maintenance service timing of when to change manual
transmission fluid.
2
Do not attempt to check or change the manual transmission fluid yourself.
■
Continuously Variable Transmission (CVT) Fluid
Specified fluid: Honda HCF-2 Transmission Fluid
■
Manual Transmission Fluid
Specified fluid: Honda Manual Transmission Fluid (MTF)
1
Continuously Variable Transmission (CVT) Fluid
NOTICE
Do not mix Honda HCF-2 with other
transmission fluids.
Using a transmission fluid other than Honda HCF-2
may adversely affect the operation and durability of
your vehicle’s transmission, and damage the
transmission.
Any damage caused by using a transmission fluid that
is not equivalent to Honda HCF-2 is not covered by
Honda’s new vehicle limited warranty.
1
NOTICE
If Honda MTF is not available, you may use the API
certificated SAE 0W-20 or 5W-20 viscosity motor oil
as a temporary measure.
Replace with MTF as soon as possible. Motor oil does
not contain the proper additives for the transmission
and continued use can cause decreased shifting
performance and lead to transmission damage.
* Not available on all models
689
uu
Maintenance Under the Bonnet
u
Brake/Clutch
*
Fluid
Main
tenan
ce
Brake/Clutch
*
Fluid
The fluid level should be between the
MIN
and
MAX
marks on the side of the reserve
tank.
The brake fluid reserve tank is also used for
your vehicle’s clutch fluid. As long as you keep
the brake fluid level as instructed above, there
is no need for checking the clutch fluid level.
Specified fluid: Brake Fluid with DOT 3 or DOT 4
■
Checking the Brake Fluid
1
NOTICE
Brake fluid marked DOT 5 is not compatible with your
vehicle’s braking system and can cause extensive
damage.
We recommend using a genuine product.
If the brake fluid level is at or below the
MIN
mark,
have a dealer inspect the vehicle for leaks or worn
brake pads as soon as possible.
Left-hand Drive Type
MAX
Reserve
Tank
MIN
Manual transmission models
Right-hand Drive Type
MAX
Reserve
Tank
MIN
* Not available on all models
690
uu
Maintenance Under the Bonnet
u
Refilling Window Washer Fluid
Main
tenan
ce
Refilling Window Washer Fluid
Check the amount of window washer fluid
using the washer fluid level gauge on the cap.
If the level is low, fill the washer reservoir.
If the washer fluid is low, a symbol appears on
the driver information interface.
Pour the washer fluid carefully. Do not overflow the reservoir.
1
NOTICE
Do not use engine antifreeze or a vinegar/water
solution in the windscreen washer reservoir.
Antifreeze can damage your vehicle’s paint. A
vinegar/water solution can damage the windscreen
washer pump.
Use only commercially available windscreen washer
fluid.
Avoid prolonged use of hard water to prevent lime
scale build up.
Models with level gauge
Level Gauge
Models without level gauge
All models
691
uu
Maintenance Under the Bonnet
u
Fuel Filter
Main
tenan
ce
Fuel Filter
Replace fuel filter according to the time and distance recommendations in the
maintenance schedule.
Have a qualified technician change the fuel filter. Fuel in the system can spray out
and create a hazard if all fuel line connections are not handled correctly.
1
The fuel filter should be replaced according to the
service reminder indication.
Models with service reminder system
692
Main
tenan
ce
Replacing Light Bulbs
Headlights
Headlights are LED type. Have an authorised Honda dealer inspect and replace the
light assembly.
1
The headlight aim is set by the factory, and does not
need to be adjusted. However, if you regularly carry
heavy items in the luggage area or tow a trailer, have
the aiming readjusted at a dealer or by a qualified
technician.
693
uu
Replacing Light Bulbs
u
Front Fog Light Bulbs
*
Continued
Main
tenan
ce
Front Fog Light Bulbs
*
When replacing, use the following bulbs.
1.
Remove the screw using a Phillips-head
screwdriver and remove the holding clips
using a flat-tip screwdriver.
2.
Pull down the under cover.
Front Fog Light: 35 W (H8 for halogen bulb type)
*
Front Fog Light: LED type
*
1
NOTICE
Halogen bulbs get very hot when lit. Oil, perspiration,
or a scratch on the glass can cause the bulb to
overheat and shatter.
When replacing a halogen bulb, handle it by its
plastic case, and protect the glass from contact with
your skin or hard objects. If you touch the glass, clean
it with denatured alcohol and a clean cloth.
Front fog lights are LED type. Have an authorised
Honda dealer inspect and replace the light assembly.
Models with halogen front fog lights
Models with LED front fog lights
Models with halogen front fog lights
Screw
Holding clip
* Not available on all models
uu
Replacing Light Bulbs
u
Front Fog Light Bulbs
*
694
Main
tenan
ce
3.
Push the tab to remove the coupler.
4.
Rotate the old bulb to the right to remove.
5.
Insert a new bulb into the fog light
assembly and turn it to the left.
6.
Insert the coupler into the connector of the
bulb.
4.
Rotate the old bulb to the left to remove.
5.
Insert a new bulb into the fog light
assembly and turn it to the right.
6.
Insert the coupler into the connector of the
bulb.
1
Insert a flat-tip screwdriver, lift and remove the centre
pin to remove the clip.
Insert the clip with the centre pin raised, and push
until it is flat.
Models with halogen front fog lights
Push until the pin
is flat.
Bulb
Coupler
Tab
Right side
Bulb
Coupler
Tab
Left side
* Not available on all models
695
uu
Replacing Light Bulbs
u
Position/Daytime Running Lights
Main
tenan
ce
Position/Daytime Running Lights
Position/daytime running lights are LED type. Have an authorised Honda dealer
inspect and replace the light assembly.
Active Cornering Lights
*
Active cornering lights are LED type. Have an authorised Honda dealer inspect and
replace the light assembly.
Front Turn Signal Lights
Front turn signal lights are LED type. Have an authorised Honda dealer inspect and
replace the light assembly.
Side Turn Signal/Emergency Indicator Lights
Door mirror side turn lights are LED type. Have an authorised Honda dealer inspect
and replace the light assembly.
Brake/Taillights and Rear Turn Signal Lights
Brake/taillights and rear turn signal lights are LED type. Have an authorised Honda
dealer inspect and replace the light assembly.
* Not available on all models
696
uu
Replacing Light Bulbs
u
Taillights and Back-Up Light Bulbs
Main
tenan
ce
Taillights and Back-Up Light Bulbs
When replacing, use the following bulbs.
1.
Remove the cover by prying on the edge
using a flat-tip screwdriver.
u
Wrap the flat-tip screwdriver with a cloth
to prevent scratches.
2.
Turn the socket to the left and remove it.
Remove the old bulb.
3.
Insert a new bulb.
Taillight: LED
Back-Up Light: 16 W
1
Taillights and Back-Up Light Bulbs
Taillights are LED type. Have an authorised Honda
dealer inspect and replace the light assembly.
Cover
Bulb
Socket
697
uu
Replacing Light Bulbs
u
Rear Licence Plate Light
Main
tenan
ce
Rear Licence Plate Light
Rear licence plate light is LED type. Have an authorised Honda dealer inspect and
replace the light assembly.
High-Mount Brake Light
High-mount brake light is LED type. Have an authorised Honda dealer inspect and
replace the light assembly.
Rear Fog Light
Rear fog light is LED type. Have an authorised Honda dealer inspect and replace the
light assembly.
698
uu
Replacing Light Bulbs
u
Other Light Bulbs
Main
tenan
ce
Other Light Bulbs
When replacing, use the following bulbs.
1.
Pry on the edge of the cover using a flat-
tip screwdriver to remove the cover.
u
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
2.
Remove the old bulb and insert a new
bulb.
■
Vanity Mirror Light Bulbs
*
Vanity Mirror Light: 1.4 W
Bulb
When replacing, use the following bulb.
1.
Pry on the edge of the cover using a flat-
tip screwdriver to remove the cover.
u
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
■
Luggage Area Light Bulb(s)
Luggage Area Light: 5 W
Models with third row seat
Models without third row seat
2.
Remove the old bulb and insert a new
bulb.
Bulb
* Not available on all models
699
uu
Replacing Light Bulbs
u
Other Light Bulbs
Main
tenan
ce
When replacing, use the following bulb.
1.
Open the glove box.
2.
Remove the old bulb and insert a new
bulb.
■
Glove Box Light Bulb
*
Glove Box Light: 3.4 W
Pull
Handle
Bulb
* Not available on all models
700
Main
tenan
ce
Checking and Maintaining Wiper Blades
Checking Wiper Blades
If the wiper blade rubber has deteriorated, it will leave streaks and the hard surfaces
of the blade may scratch the window glass.
Changing the Front Wiper Blade Rubber
1.
Turn the ignition switch to LOCK
(
0
*1
.
2.
While holding the wiper switch in the
MIST
position, turn the ignition switch to
ON
(
w
*1
, then to LOCK
(
0
*1
.
u
Both wiper arms are set to the
maintenance position as shown in the
image.
3.
Lift both wiper arms.
*1: Models with the keyless access system have an
ENGINE START/STOP
button instead of an
ignition switch.
1
Changing the Front Wiper Blade Rubber
NOTICE
Avoid dropping the wiper arm onto the windscreen,
it may damage the wiper arm and/or the windscreen.
701
uu
Checking and Maintaining Wiper Blades
u
Changing the Front Wiper Blade Rubber
Continued
Main
tenan
ce
4.
Press up on and hold the tab, then slide
the holder off the wiper arm.
5.
Pull the end of the wiper blade in the
direction of the arrow in the image until it
is out of the holder’s end cap.
6.
Pull the wiper blade in the opposite
direction to slide it out of the holder.
Tab
Blade
End Cap At
The Bottom
Blade
Holder
702
uu
Checking and Maintaining Wiper Blades
u
Changing the Front Wiper Blade Rubber
Main
tenan
ce
7.
Insert the flat side of the new wiper blade
onto the bottom part of the holder. Insert
the blade all the way.
8.
Install the end of the wiper blade into the
cap.
9.
Slide the holder onto the wiper arm until it
locks.
10.
Lower both wiper arms.
11.
Turn the ignition switch to ON
(
w
*1
and
hold the wiper switch in the
MIST
position
until both wiper arms return to the
standard position.
*1: Models with the keyless access system have an
ENGINE START/STOP
button instead of an
ignition switch.
Holder
Blade
Cap
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст