Honda Odyssey 2004. Manual — part 532
−
−
−
−
−
−
01
02
S0X4AZ4K79100081013FAAT00
’99-01 Models
DTC 1-3:
YES
NO
YES
NO
YES
NO
23-70
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
07TAZ-SZ5011A
07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in Driver’s Airbag Inflator
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 2P connector from
the cable reel 2P connector (A).
5. Connect the special tool (2
connector) to the
cable reel 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short in the driver’s airbag inflator; replace
the driver’s airbag (see page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the cable reel 2P connector from the
SRS main harness 2P connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short in the cable reel; replace the cable reel
(see page 23-376).
Does the SRS indicator stay on?
Is DT C 1-3 indicated?
Is DT C 1-3 indicated?
03/07/29 10:32:56 61S0X050_230_0070
−
−
03
03
05
YES
NO
23-71
A
B
A
SRS MAIN HARNESS 18P CONNECTOR
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
16. Disconnect the front passenger’s airbag 2P
connector (A) and both seat belt tensioner 2P
connectors (B).
17. Disconnect the special tool from the SRS main
harness 2P connector.
18. Disconnect the SRS main harness 18P connector
(A) from the SRS unit.
19. Check resistance between the No. 1 terminal and
the No. 13 terminal of the SRS main harness 18P
connector. There should be an open circuit, or at
least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Short in the SRS main harness; replace the
SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:32:57 61S0X050_230_0071
−
−
−
−
−
−
01
02
S0X4AZ4K79100081014FAAT00
’99-01 Models
DTC 1-4:
YES
NO
YES
NO
YES
NO
23-72
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
07TAZ-SZ5011A
07SAZ-TB4011A
Short to Power in Driver’s Airbag
Inflator
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 2P connector from
the cable reel 2P connector (A).
5. Connect the special tool (2
connector) to the
cable reel 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the driver’s airbag inflator;
replace the driver’s airbag (see page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the cable reel 2P connector from the
SRS main harness 2P connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to power in the cable reel; replace the
cable reel (see page 23-376).
Does the SRS indicator stay on?
Is DT C 1-4 indicated?
Is DT C 1-4 indicated?
03/07/29 10:32:58 61S0X050_230_0072
−
−
03
03
05
YES
NO
23-73
A
B
A
SRS MAIN HARNESS 18P CONNECTOR
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
16. Disconnect the front passenger’s airbag 2P
connector (A) and both seat belt tensioner 2P
connectors (B).
17. Disconnect the SRS main harness 18P connector
(A) from the SRS unit.
18. Reconnect the battery negative cable.
19. Turn the ignition switch ON (II).
20. Check for voltage between the No. 1 terminal of the
SRS main harness 18P connector and body ground,
and between the No. 13 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Short to power in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Is the voltage as specif ied?
03/07/29 10:32:58 61S0X050_230_0073
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст