Honda Odyssey 2004. Manual — part 450
Cavity
Wire
Test condition
Test: Desired result
Possible cause if result is not
obtained
22-128
Exterior Lights
Daytime Running Lights Control Unit Input Test (cont’d)
4. Make these input tests at the connector.
• If any test indicates a problem, find and correct the cause, then recheck the system.
• If all the input tests prove OK, the control unit must be faulty; replace it.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
RED/ORN
Combination light
switch ON (
),
and dimmer switch
in HIGH
Connect a jumper wire between
No. 1 and No. 2 terminals and
connect No. 11 terminal to
ground:
The headlights (HIGH) and high
beam indicator light should
come on.
Blown No. 55 (40A) fuse in
the under-hood fuse/relay
box
Blown No. 6 (10A) fuse in the
passenger’s under-dash fuse/
relay box
Blown headlight bulb (High
beam)
Blown high beam indicator
light
An open in the wire
Poor ground (G401)
11
RED/WHT
2
RED/BLU
Under all
conditions
Check for voltage to ground:
There should be battery voltage.
Blown No. 55 (40A) fuse in
the under-hood fuse/relay
box
Blown No. 6 (10A) fuse in the
passenger’s under-dash fuse/
relay box
An open in the wire
4
BLK
Under all
conditions
Check for continuity to ground:
There should be continuity.
Poor ground (G401)
An open in the wire
7
6
GRN/WHT
Parking brake
pedal pressed
Check for continuity to ground:
There should be continuity.
Faulty parking brake switch
An open in the wire
8
BLU/RED
Headlights OFF
Check for voltage to ground:
There should be battery voltage.
Faulty headlight relay 1
An open in the wire
9
BLU/WHT
Ignition switch ON
(II)
Connect to ground:
The indicator light should come
on.
Faulty DRL indicator light
An open in the wire
10
RED/YEL
Combination light
switch ON (
),
and dimmer switch
in HIGH
Check for voltage to ground:
There should be battery voltage.
Blown No. 45 (15A) fuse in
the under-hood fuse/relay
box
Faulty combination light
switch
Faulty headlight relay 2
An open in the wire
3
ORN/WHT
Combination light
switch ON (
)
Check for continuity to ground:
There should be continuity.
Faulty combination light
switch
Poor ground (G401)
An open in the wire
5
12
YEL/RED
Ignition switch ON
(II)
Check for voltage to ground:
There should be battery voltage.
Blown No. 5 (7.5A) fuse in the
driver’s under-dash fuse/relay
box
An open in the wire
13
GRN/RED
Brake fluid
reservoir float in
down position
Check for continuity to ground:
There should be continuity.
Faulty brake fluid level switch
An open in the wire
Poor ground (G302)
03/07/29 10:21:22 61S0X050_220_0130
01
S0X4A00J32133131131KBAT00
HEADLIGHT
(High):
60 W
(Low):
55 W
FRONT TURN SIGNAL/
SIDE MARKER LIGHT:
21/5 W
22-129
Headlight Replacement
A
Headlights become very hot during use; do not
touch them or any attaching hardware immediately
after they have been turned off.
1. Remove the front bumper (see page 20-128).
2. Disconnect the connectors (A) from the headlight.
3. Remove the four mounting bolts, then remove the
headlight assembly.
4. Install the headlight in the reverse order of removal.
5. After replacement, adjust the headlights to local
requirements (see page 22-130).
03/07/29 10:21:23 61S0X050_220_0131
01
02
03
S0X4A00J32133131131MBAT00
Before adjusting the headlights
22-130
Exterior Lights
Headlight Adjustment
A
A
7.5 m (25 ft)
Headlight become very hot during use; do not
touch them or any attaching hardware immediately
after they have been turned off.
• Park the vehicle on level surface.
• Make sure the tire pressures are correct.
• The driver or someone who weighs the same should
sit in the driver’s seat.
1. Clean the outer lens so that you can see the center
of the headlights (A).
2. Park the vehicle 7.5 m (25 ft) from a wall or a screen
(A).
3. Open the hood.
4. Turn the horizontal adjuster so that the arrow on
the horizontal indicator gear (A) is pointing up.
(’99-00 models)
03/07/29 10:21:23 61S0X050_220_0132
*01
01
06
Vertical adjustment:
Horizontal adjustment (’99-00 models):
22-131
A
E
D
B
C
B
A (’99-00 models)
B
A
C
5. Turn the low beams on.
6. Determine if the headlights are aimed properly.
Measure the height of the headlights (A). The lights
should reflect 52 mm (2.1 in.) below headlight
height (B).
The width of the refracting points (C) should be the
same as the width of the headlight central points (D,
E).
7. If necessary, adjust the headlights to local
requirements by turning the horizontal adjuster (A)
(’99-00 models) and the vertical adjuster (B).
8. After headlight replacement;
On ’99-00 models, push and install the horizontal
indicator gear (A) to the horizontal adjuster (B) so
that the arrow on the indicator gear (C) is pointing
up.
03/07/29 10:21:24 61S0X050_220_0133
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст