Honda Odyssey 2004. Manual — part 538
−
−
−
−
−
−
01
*01
S0X4AZ4K79100081044FAAT00
’99-01 Models
DTC 4-4:
YES
NO
YES
NO
YES
NO
23-94
SRS
DTC Troubleshooting (cont’d)
07TAZ-SZ5011A
07SAZ-TB4011A
A
A
07TAZ-SZ5011A
07SAZ-TB4011A
C581
Short to Power in Front Passenger’s
Seat Belt Tensioner
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the right side wire
harness 2P connector (A).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10.
connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to power in the right side wire harness;
replace the right side wire harness.
Does the SRS indicator stay on?
Is DT C 4-4 indicated?
Is DT C 4-4 indicated?
03/07/29 10:33:13 61S0X050_230_0094
Disconnect the SRS main harness 2P
connector C581 from the right side wire harness 2P
−
−
03
03
05
YES
NO
23-95
A
B
C
A
SRS MAIN HARNESS 18P CONNECTOR
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and driver’s seat
belt tensioner connector (C).
17. Disconnect the SRS main harness 18P connector
(A) from the SRS unit, and disconnect the special
tool from the SRS main harness 2P connector.
18. Reconnect the battery negative cable.
19. Turn the ignition switch ON (II).
20. Check for voltage between the No. 5 terminal of the
SRS main harness 18P connector and body ground,
and between the No. 12 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit or poor contact at the SRS
main harness 18P connector at the SRS unit. Check
the connection; if the connection is OK, replace the
SRS unit (see page 23-382).
Short to power in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Is the voltage as specif ied?
03/07/29 10:33:14 61S0X050_230_0095
−
−
−
−
−
−
01
*01
S0X4AZ4K79100081045FAAT00
’99-01 Models
DTC 4-5:
YES
NO
YES
NO
YES
NO
23-96
SRS
DTC Troubleshooting (cont’d)
07TAZ-SZ5011A
07SAZ-TB4011A
A
A
07TAZ-SZ5011A
07SAZ-TB4011A
C581
Short to Ground in Front Passenger’s
Seat Belt Tensioner
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the right side wire
harness 2P connector (A).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to ground in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10.
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to ground in the right side wire harness;
replace the right side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 4-5 indicated?
Is DT C 4-5 indicated?
03/07/29 10:33:14 61S0X050_230_0096
connector (A).
Disconnect the SRS main harness 2P
connector C581 from the right side wire harness 2P
−
−
03
03
05
YES
NO
23-97
A
B
C
A
SRS MAIN HARNESS 18P CONNECTOR
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and driver’s seat
belt tensioner connector (C).
17. Disconnect the SRS main harness 18P connector
(A) from the SRS unit, and disconnect the special
tool from the SRS main harness 2P connector.
18. Check resistance between the No. 5 terminal of the
SRS main harness 18P connector and body ground,
and between the No. 12 terminal and body ground.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit or poor contact at the SRS
main harness 18P connector at the SRS unit. Check
the connection; if the connection is OK, replace the
SRS unit (see page 23-382).
Short to ground in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:33:15 61S0X050_230_0097
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст