Honda Odyssey 2004. Manual — part 316
−
−
−
−
−
−
−
−
*02
01
02
03
YES
NO
YES
NO
YES
NO
YES
NO
19-70
ABS Components
DTC Troubleshooting (cont’d)
MODULATOR UNIT CONNECTOR
SOLENOID
(BRN/BLK)
ABS CONTROL UNIT CONNECTOR A (22P)
FSR (YEL/GRN)
ABS CONTROL UNIT CONNECTOR A (22P)
FSR (YEL/GRN)
ABS FAIL-SAFE RELAY CONNECTOR
GND (BLK)
9. Measure the voltage between the modulator unit
connector terminal No. 10 and body ground.
Repair short to power in the wire between
the ABS fail-safe relay, modulator unit, and ABS
relay box.
Go to step 10.
10. Disconnect the ABS control unit connector A (22P).
11. Turn the ignition switch ON (II).
12. Measure the voltage between terminal No. 21 and
body ground.
Repair short to power in the wire between
the ABS control unit and the ABS fail-safe relay.
Go to step 13.
13. Check for continuity between the ABS control unit
connector terminal No. 21 and body ground.
Repair short to body ground in the wire
between the ABS control unit and the ABS fail-safe
relay.
Go to step 14.
14. Check for continuity between the ABS fail-safe
relay connector terminal No. 3 and body ground.
Go to step 15.
Check for an open in the wire between the
ABS fail-safe relay and body ground. If the wire is
OK, check for poor ground at G201.
Terminal side of female terminals
Wire side of female terminals
Wire side of female terminals
Terminal side of female terminals
Is ther e batter y voltage?
Is ther e batter y voltage?
Is ther e continuity?
Is ther e continuity?
03/07/29 09:55:54 61S0X050_190_0070
−
−
−
−
−
−
04
03
S0X4A07K70100081610FAAT00
YES
NO
YES
NO
YES
NO
DTC 61, 62:
19-71
19-71
ABS FAIL-SAFE RELAY CONNECTOR
GND (BLK)
JUMPER WIRE
FSR (YEL/GRN)
ABS CONTROL UNIT CONNECTOR A (22P)
FSR (YEL/GRN)
15. Connect the ABS fail-safe relay connector terminals
No. 3 and No. 4 with a jumper wire.
16. Check for continuity between the ABS control unit
connector terminal No. 21 and body ground.
If the problem recurs, replace the ABS
control unit.
Repair open in the wire between the ABS
control unit and the ABS fail-safe relay.
1. Clear the DTC (see step 1 on page 19-43).
2. Test-drive the vehicle at 6 mph (10 km/h) or more.
Go to step 3.
The system is OK at this time.
3. Verify the DTC.
Check the charging system.
Do the appropriate troubleshooting for the
code.
Battery Voltage
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Does the ABS indicator come on?
Is DT C 61 or 62 indicated?
03/07/29 09:55:54 61S0X050_190_0071
−
−
−
−
S0X4A07K70100081710FAAT00
S0X4A07K70100081810FAAT00
DTC 71:
DTC 81:
YES
NO
YES
NO
19-72
19-72
ABS Components
DTC Troubleshooting (cont’d)
Different Diameter Tire
Central Processing Unit (CPU)
Diagnosis, and ROM/RAM Diagnosis
1. Clear the DTC (see step 1 on page 19-43).
2. Test-drive the vehicle.
Make sure all four tires are the specified
size.
Intermittent failure; the vehicle is OK at this
time.
1. Clear the DTC (see step 1 on page 19-43).
2. Test-drive the vehicle.
Replace the ABS control unit.
Intermittent failure; the vehicle is OK at this
time.
Does the ABS indicator come on, and is DT C 7 1
indicated?
Does the ABS indicator come on, and is DT C 81
indicated?
03/07/29 09:55:54 61S0X050_190_0072
−
−
−
−
−
−
−
−
−
−
−
−
11
12
S0X4A07D10600012332FAAT10
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
19-73
ABS Indicator Circuit Troubleshooting
GAUGE ASSEMBLY CONNECTOR C (16P)
WALP (BLU/WHT)
GAUGE ASSEMBLY CONNECTOR B (22P)
JUMPER WIRE
GND (BLK)
1. Turn the ignition switch ON (II), and watch the ABS
indicator.
If the ABS indicator comes on and goes off,
It’s OK. If the ABS indicator stays on, go to step 13.
Go to step 2.
2. Turn the ignition switch OFF then ON (II) again.
Go to step 3.
Repair open in the indicator power source
circuit.
• Blown BACKUP LIGHT (7.5A) fuse.
• Open in the wire between the BACKUP LIGHT
(7.5A) fuse and the gauge assembly.
• Open circuit inside the fuse box.
3. Turn the ignition switch OFF.
4. Disconnect the ABS control unit connector A (12P).
5. Turn the ignition switch ON (II).
Check for loose ABS control unit connectors.
If necessary, substitute a known-good ABS control
unit, and recheck.
Go to step 6.
6. Check the ABS indicator bulb in the gauge
assembly.
Go to step 7.
Replace the ABS indicator bulb.
7. Turn the ignition switch OFF.
8. Disconnect the gauge assembly connector C (16P).
9. Check for continuity between the gauge assembly
connector C (16P) terminal No. 10 and body ground.
Repair short to body ground in the wire
between the gauge assembly and the ABS control
unit.
Go to step 10.
10. Connect the gauge assembly connector C (16P).
11. Connect the gauge assembly connector B (22P)
terminal No. 16 to body ground with a jumper wire.
12. Turn the ignition switch ON (II).
Repair open in the wire between the gauge
assembly and body ground (G503).
Replace the printed circuit board in the gauge
assembly.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Does the ABS indicator come on?
Does the br ake system indicator come on?
Does the ABS indicator come on?
Is the bulb OK ?
Is ther e continuity?
Does the ABS indicator come on?
03/07/29 09:55:55 61S0X050_190_0073
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст