Honda Odyssey 2004. Manual — part 463
*01
S0X4A00J34300044051EAAT25
−
−
22-180
Power Mirrors
Circuit Diagram - without Defogger
POWER MIRROR SWITCH
4
1
YEL/BLK
DOWN
RIGHT
LEFT
UP
2
10
9
8
7
RIGHT
LEFT
LEFT
RIGHT
No.4 (7.5A)
YEL
IGNITION SWITCH
IG2
BAT
BLU/WHT
BLU/GRN
YEL/WHT
BLU/ORN
BLU/WHT
BLU/WHT
UNDER HOOD FUSE/RELAY BOX
LEFT MIRROR
RIGHT MIRROR
2
2
1
3
3
1
UP
RIGHT
LEFT
DOWN
DOWN
LEFT
RIGHT
UP
LT GRN
G501
BLK
WHT
No.42 (50A)
No.41 (120A)
BATTERY
DRIVER’S
UNDER DASH
FUSE/RELAY BOX
03/07/29 10:22:49 61S0X050_220_0182
*02
S0X4A00J34300044051EAAT20
−
−
22-181
Circuit Diagram - with Defogger
3
YEL/BLK
6
ORN/WHT
ORN/WHT
ORN/WHT
G581
G401
BLK
1
2
DEFOGGER
DEFOGGER
2
1
BLK
BLU/WHT
BLU/GRN
YEL/WHT
BLU/ORN
BLU/WHT
BLU/WHT
LEFT MIRROR
RIGHT MIRROR
5
5
4
6
6
4
UP
RIGHT
LEFT
DOWN
DOWN
LEFT
RIGHT
UP
LT GRN
G501
POWER MIRROR SWITCH
4
1
YEL/BLK
DOWN
RIGHT
LEFT
UP
2
10
9
8
7
RIGHT
LEFT
LEFT
RIGHT
No.4 (7.5A)
YEL
IGNITION SWITCH
IG2
BAT
UNDER HOOD FUSE/RELAY BOX
BLK
WHT
No.42 (50A)
No.41 (120A)
BATTERY
DRIVER’S
UNDER DASH
FUSE/RELAY BOX
DEFOGGER
SWITCH
03/07/29 10:22:50 61S0X050_220_0183
01
S0X4A00J34300044051FEAT00
Both mirrors
Left mirror
Right mirror
Defogger (Canada)
22-182
Power Mirrors
Function Test
B
A
YEL/BLK
BLK
YEL/BLK
(Canada)
BLU/WHT
ORN/WHT
(Canada)
BLU/GRN
YEL/WHT
BLU/ORN
LT GRN
1. Remove the dashboard lower cover
(see page 20-69).
2. Push the power mirror switch (A) out from behind
the dashboard.
3. Disconnect the 10P connector (B) from the switch,
then remove the switch.
4. Choose the appropriate test based on the
symptom:
• Both mirrors don’t work, go to step 5.
• Left mirror doesn’t work, go to step 7.
• Right mirror doesn’t work, go to step 8.
• Defoggers don’t work, go to step 9 (Canada).
5. Check for voltage between the No. 1 terminal and
body ground with the ignition switch ON (II).
There should be battery voltage.
• If there is no battery voltage, check for:
– blown No. 4 (7.5A) fuse in the driver’s under-
dash fuse/relay box.
– an open in the YEL/BLK wire.
• If there is battery voltage, go to step 6.
6. Check for continuity between the No. 2 terminal
and body ground.
There should be continuity.
• If there is no continuity, check for:
– an open in the BLK wire.
– poor ground (G 501).
• If there is continuity, check both mirrors
individually as described in the next column.
7. Connect the No. 1 terminal to the No. 7 terminal,
and the No. 4 (or No. 9) terminal to body ground
with jumper wires. The left mirror should tilt down
(or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the BLU/WHT (or BLU/
ORN) wire between the left mirror and the 10P
connector. If the wire is OK, check the left mirror
actuator.
• If the mirror neither tilts down nor swings left,
repair the BLU/GRN wire.
• If the mirror works properly, check the mirror
switch.
8. Connect the No. 1 terminal to the No. 8 terminal,
and the No. 4 (or No. 10) terminal to body ground
with jumper wires. The right mirror should tilt
down (or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the BLU/WHT (or LT
GRN) wire between the right mirror and the 10P
connector.
If the wire is OK, check the right mirror actuator.
• If the mirror neither tilts down nor swings left,
repair the YEL/WHT wire.
• If the mirror works properly, check the mirror
switch.
9. Connect the No. 3 and No. 6 terminals with a
jumper wire, and check for voltage between the
No. 3 terminal and body ground. There should be
battery voltage and both mirrors should warm up
with the ignition switch ON (II).
• If there is no voltage or neither warms up, check
for:
– an open in the YEL/BLK or ORN/WHT wire.
– blown No. 4 (7.5A) fuse in the driver’s under-
dash fuse/relay box.
– poor ground (G401 or G581).
• If only one fails to warm up, check its defogger.
• If both warm up, check the defogger switch.
Wire side of
female terminals
03/07/29 10:22:50 61S0X050_220_0184
01
*01
*02
S0X4A00J34300044041FEAT00
Mirror Switch:
Defogger Switch (Canada):
22-183
Power Mirror and Mirror Defogger Switch Test
A
B
Terminal
Position
UP
DOWN
LEFT
RIGHT
L
UP
DOWN
LEFT
RIGHT
R
1
2
4
7
8
9
10
Terminal
Position
ON
OFF
3
6
1. Remove the dashboard lower cover (see page 20-
69).
2. Disconnect the 10P connector (A) from the power
mirror switch (B).
3. Check for continuity between the terminals in each
switch position according to the table.
4. If the continuity is not as specified, replace the
switch.
03/07/29 10:22:51 61S0X050_220_0185
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст