Honda Odyssey 2004. Manual — part 295
05
*02
*03
*04
Reassembly
Installation
18-20
Front Suspension
Damper/Spring Replacement (cont’d)
A
B
C
A
C
A
B
10 x 1.25 mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
16 x 1.5 mm
157 N·m
(16.0 kgf·m, 116 lbf·ft)
D
C
12 x 1.25 mm
78 N·m
(8.0 kgf·m,
58 lbf·ft)
A
22 N·m
(2.2 kgf·m,
16 lbf·ft)
E
F
B
12 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
1. Install the damper unit on a commercially available
strut spring compressor (A).
2. Assemble the damper in reverse order of removal
except for the washer and self-locking nut. Align
the bottom of the damper spring and the spring
lower seat (B).
3. Compress the damper spring.
4. Install the damper mounting washer (A) and a new
12 mm self-locking nut (B).
5. Hold the damper rod using a hex wrench (C), and
tighten the 12 mm self-locking nut.
1. Loosely install the damper (A) onto the frame, then
loosely install the three flange nuts (B).
NOTE: At this stage, do not install the service cap
(C).
2. Install the damper.
–1 Loosely install the damper pinch bolts (A) and
flange nuts (B) to the damper (C).
–2 Loosely install the stabilizer link (D) to the
damper.
–3 Install the brake hose bracket (E) to the damper.
–4 Install the wheel sensor wire (F) to the damper.
03/07/29 09:51:15 61S0X050_180_0020
18-21
3. Raise the knuckle with a floor jack until the vehicle
just lifts off the safety stands.
4. Tighten the damper pinch bolts and flange nuts.
5. Tighten the flange nuts on top of the damper to the
specified torque value.
6. Install the service caps.
7. Install the front wheel.
8. Check the front wheel alignment, and adjust it if
necessary (see page 18-5).
03/07/29 09:51:15 61S0X050_180_0021
*01
*06
S0X4A00B44100032501KBAT00
Exploded View
REAR DRUM BRAKE TYPE: ’99-01 models
REAR DISC BRAKE TYPE: ’02-04 models
18-22
Rear Suspension
Hub/Bearing Replacement
KNUCKLE
HUB
(includes bearing)
SPINDLE NUT 24 x 1.5 mm
245 N·m (25.0 kgf·m, 181 lbf·ft)
HUB CAP
WHEEL NUTS 12 x 1.5 mm
108 N·m (11.0 kgf·m, 79.6 lbf·ft)
FLANGE BOLTS
10 x 1.25 mm
35 N·m (3.5 kgf·m, 25 lbf·ft)
CENTER
CAP
BRAKE DRUM
BRAKE SHOE
BACKING PLATE
KNUCKLE
HUB
(includes bearing)
SPINDLE NUT
24 x 1.5 mm
245 N·m
(25.0 kgf·m,
181 lbf·ft)
HUB CAP
BRAKE DISC/DRUM
12 x 1.25 mm
93 N·m (9.5 kgf·m, 69 lbf·ft)
10 x 1.25 mm
38 N·m
(3.9 kgf·m,
28 lbf·ft)
PARKING BRAKE SHOE
ASSEMBLY
6 mm BRAKE DISC
RETAINING FLAT SCREWS
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
Replace.
Replace.
Apply a small amount of engine oil
to the seating surface.
Replace.
Replace.
Apply a small amount
of engine oil to the
seating surface.
03/07/29 09:51:16 61S0X050_180_0022
*02
03
04
REAR DRUM BRAKE TYPE: ’99-01 models
18-23
C
B
A
12 x 1.5 mm
108 N·m (11.0 kgf·m,
79.6 lbf·ft)
D
24 x 1.5 mm
245 N·m (25.0 kgf·m,
181 lbf·ft)
8 x 1.25 mm
1. Raise the rear of the vehicle, and support it with
safety stands in the proper locations
(see page 1-15).
2. Remove the wheel nuts (A) and rear wheel (B).
3. Press the parking brake pedal.
4. Remove the hub cap (C).
5. Raise the locking tab on the spindle nut (D), then
remove the nut.
6. Release the parking brake pedal.
7. Screw two 8 x 1.25 mm bolts into the drum to push
it away from the hub bearing unit. Turn each bolt
two turns at a time to prevent cocking the brake
drum excessively. Remove the brake drum from
the hub bearing unit. If the drum does not come off
easily, back off the brake adjuster one full turn
(23 teeth).
8. Remove the hub bearing unit.
9. Install the hub bearing unit in the reverse order of
removal, and pay particular attention to the
following items:
• Wash the bearing and spindle thoroughly in high
flash point solvent before reassembly.
• Before installing the new spindle nut, apply a
small amount of engine oil to the seating surface
of the nut.
• After tightening, use a drift to stake the spindle
nut shoulder against the spindle.
• Inspect the pulser teeth for any damage.
(cont’d)
03/07/29 09:51:17 61S0X050_180_0023
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст