Honda Odyssey 2004. Manual — part 512
*01
*02
01
S0X4A82J36100000000FEAT00
+
−
+
+
Start-up procedure
System Links
Tire Calibrate
22-376
Navigation System
System Diagnosis Test
Diagnosis Menu
System Links
Tire-Calibrate
In-Line Diag
Monitor Check
Unit Check
Yaw Rate
Cyclic Diag
Rear Camera
Return
DIAGNOSIS MENU SCREEN
’03-04 Models Only
System Links
ANT
Disp
A/C
Navi ECU
OK
Rerutn
GPS
Tire-Calibrate
Tire-Cal Factor
Auto-Tuning
STD
7.0%
Set
ON
Tire-Cal Tuning
7.0%
Return
1. Turn the ignition switch ON (II), select ‘‘OK’’ on the
Disclaimer screen then press and hold the buttons
in this order: (1) MENU button. (2) MAP/GUIDE
button, (3) CANCEL button, and keep them pressed
2. After the display changes to the diagnosis menu
screen, select the item you want to check, and the
check will start. To return to the previous screen,
select the ‘‘RETURN’’ on the screen.
• System Links.
• Tire Calibrate.
• Monitor Check.
• Yaw Rate.
• Unit Check.
• Cyclic Diag.
• Rear camera. (’03-04 Models Only)
• In-line Diag.
• During diagnosis, all of the communication lines
connecting the components are shown in yellow.
• If the system is OK, all of the communication lines
connecting the components will change to green, the
screen will indicate ‘‘OK’’, and a tone will sound.
• If there is a problem in the system, the faulty
communication line will change to red, the screen
will indicate ‘‘NG’’, and a tone will sound.
NOTE: If the A/C link is red, refer to climate control
manual switch troubleshooting (see page 21-116).
• The indication on the screen will not change until the
ignition switch is cycled. After repairing the system,
turn the ignition switch OFF to reset the system, then
return to the Diagnosis Menu screen, and run system
Links again.
• The ‘‘AUTO TUNING’’ is factory-set to ‘‘ON’’, and it
should remain on. If you find it has been turned OFF,
turn it back ON.
• The ‘‘TIRE-CAL TUNING’’ should not be used. The
AUTO TUNING function keeps the system in better
tune.
03/07/29 10:28:47 61S0X050_220_0378
for 5 seconds.
±
±
*03
*04
Yaw Rate
Cyclic Diag
In-Line Diag
Rear Camera (Accessory) (’03-04 Models
Only)
Good
Offset
2.517 V
Sensor
2.517 V (0.010 V
)
Bad
Offset
2.517 V
Sensor
2.823 V
22-377
Yaw Rate
Offset
Sensor
CCW-Cal Factor
CW-Cal Factor
2.517 V
2.517 V
0.0 %
0.0 %
Return
Tuning
Monitor
Rear Camera Setting:
If the Rear-Camera is installed,
set the switch to ON.
Rear-Camera switch:
If No Rear-Camera is installed,
set the switch to OFF.
Off
Return
‘‘Offset’’ is a reference voltage or standard within the
yaw rate sensor. It should indicate 1.500 to 3.500 V with
the vehicle stopped.
‘‘Sensor’’ indicates the voltage output from the yaw
rate sensor. It should indicate 1.500 to 3.500 V with the
vehicle stopped.
A ‘‘sensor’’ output voltage HIGHER than that of the
‘‘Offset’’ voltage indicates the vehicle is turning to the
RIGHT.
A ‘‘sensor’’ output voltage LOWER than that of the
‘‘Offset’’ voltage indicates the vehicle is turning to the
LEFT.
With the vehicle stopped, sitting still, with the engine
idling, both the ‘‘Offset’’ and ‘‘Sensor’’ voltage should
be within 0.01 V
of each other.
If not, replace the navigation unit.
Example:
NOTE: The vehicle is stopped, sitting still, with the
engine idling.
NOTE: Do not try to tune the yaw rate sensor unless
instructed by American Honda.
This test checks the following items repeatedly:
• Navigation unit check
• Monitor check (except switch test)
To exit this test, press the CANCEL key
This test checks following items:
• System links
• Car status
• Yaw rate
This screen is used to turn on or off the rear camera
setting. When the setting is turned on, the navigation
system will know that the rear camera accessory is
installed, and the following changes occur within the
navigation system:
• Normally, if you do not touch ‘‘OK’’ on the Disclaimer
screen, the navigation display screen turns off after
30 seconds. If you select Rear-Camera switch ‘‘On’’,
the rear camera to operate even if the navigation
screen is deliberately turned off, or goes off
automatically if the disclaimer screen is ignored.
• The navigation touch screen and hard buttons are
ignored when the transmission is in reverse. This
prevents accidental touch screen/hard button
commands that can cancel your route, or disturb the
screen you are viewing.
(cont’d)
03/07/29 10:28:47 61S0X050_220_0379
02
*05
*06
Monitor Check
RGB Color
White Raster
22-378
Navigation System
System Diagnosis Test (cont’d)
Return
Monitor Check
RGB Color
Test Pattern
White Raster
Switch Check
Black Raster
Color Change
Red
Green
Blue
Return
Return
Select the item you want to check, and the check starts.
The three primary colors of red, green and blue must be
shown. If any color is missing, troubleshoot for the
missing color (see page 22-367).
The entire display must be shown in white.
03/07/29 10:28:48 61S0X050_220_0380
*07
*08
*09
03
Switch Check
Test Pattern
Black Raster
Color Change
22-379
Return
Return
Return
Color Change
BASE- 0
Set
Default
R
30
G
60
B
30
Return
Color No.
Each switch must be shown on the display and each
switch must reverse and sound, when touched.
NOTE: The test may be affected if done in direct
sunlight.
All 32 colors including black must be indicated
(including the back ground color).
The entire display must be shown in black.
This screen is for the manufacturer’s use only.
(cont’d)
03/07/29 10:28:48 61S0X050_220_0381
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст