Honda Odyssey 2004. Manual — part 455
01
02
S0X4A00J32323335061FEAT01
01
S0X4A00J32300058311FEAT02
22-148
22-148
Interior Lights
Interior Light Switch Test
Tailgate Latch Switch Test
A
C
B
A
Terminal
Position
MIDDLE
OFF
6
1
2
3
5
4
ON
1. Remove the center panel (see page 20-70).
2. Push the switch (A) out from the center panel.
3. Disconnect the 6P connector (B) from the switch.
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified, replace the bulb
(C) or the switch.
1. Open the tailgate.
2. Remove the tailgate lower trim (see page 20-61).
3. Disconnect the 2P connector (A) from the latch
switch.
4. Check for continuity between the No. 1 and No. 2
terminals.
• With the tailgate open, there should be continuity.
• With the tailgate closed, there should be no
continuity.
5. If the continuity is not as specified, replace the
tailgate latch switch.
Terminal side of
male terminals
03/07/29 10:21:37 61S0X050_220_0150
11
12
13
S0X4A00J32300039851FEAT10
FRONT MAP LIGHT BULB: 6.2 W
22-149
Front Individual Map Light Test
D
C
B
A
Terminal
Position
OFF
1
2
3
ON
LEFT
RIGHT
OFF
ON
1. Carefully pry off the lens (A) with a small
screwdriver.
2. Remove the four mounting screws (B).
3. Disconnect the 3P connector (C) from the housing
(D).
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified, check the
bulb(s). If the bulb(s) are OK, replace the light.
03/07/29 10:22:27 61S0X050_220_0151
21
22
23
S0X4A00J32300039851FEAT20
REAR MAP LIGHT BULB: 10 W
22-150
Interior Lights
Rear Individual Map Light Test
A
B
D
C
Terminal
Position
OFF
1
2
3
ON
LEFT
RIGHT
OFF
ON
1. Carefully pry off the lens (A) with a small
screwdriver.
2. Remove the mounting screw (B).
3. Disconnect the 3P connector (C) from the housing
(D).
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified check the bulb. If
the bulb is OK, replace the light.
03/07/29 10:22:28 61S0X050_220_0152
01
02
01
S0X4A00J32323316151FEAT00
CARGO AREA LIGHT BULB:
8 W
22-151
Cargo Area Light Test
D
C
B
A
3
3’
4
1’
2
1
Terminal
Position
MIDDLE
OFF
2
ON
1 or 1’ 3 or 3’
4
1. Turn the light switch OFF.
2. Carefully pry off the lens (A) with a small
screwdriver.
3. Remove the two mounting screws (B) and the
housing (C).
4. Disconnect the 3P connector (D) from the housing.
5. Check for continuity between the terminals in each
switch position according to the table.
6. If the continuity is not as specified check the bulb. If
the bulb is OK, replace the light.
03/07/29 10:22:28 61S0X050_220_0153
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст