Honda Odyssey 2004. Manual — part 515
01
01
01
01
01
01
01
01
01
S0X4A000000000J2301PAAT00
Ref.No.
Tool Number
Description
Qty
23-2
Restraints
Special Tools
1
2
07HAZ-SG00500
Deployment Tool
1
07PAZ-0010100
SCS Service Connector
1
07SAZ-TB4011A
SRS Inflator Simulator
1
07TAZ-SZ5011A
SRS Simulator Lead C
1
07TAZ-001020A
Backprobe Adapter, 17 mm
2
07XAZ-S1A0200
SRS Simulator Lead E
1
07XAZ-SZ30100
SRS Simulator Lead F
1
07YAZ-S3AA100
SRS Simulator Lead H
1
070AZ-SAA0100
SRS Short Canceler
1
1: Included in SRS Tool Set 07MAZ-SM5000B
2: Use with the stacking patch cords from T/N 07SAZ-001000A, Backprobe Set.
03/07/29 10:30:29 61S0X050_230_0002
*01
S0X4A00H46200000000DAAT00
23-3
Seat Belts
Component Location Index
SECOND ROW SHOULDER ANCHOR ADJUSTER
THIRD ROW CENTER
SHOULDER SEAT BELT
THIRD ROW SEAT BELT BUCKLES/
CENTER LAP BELT TONGUE
FRONT SHOULDER ANCHOR ADJUSTER
SECOND ROW SEAT BELT BUCKLES
FRONT SEAT
BELT BUCKLES
THIRD ROW CHILD SEAT TETHER ANCHOR
THIRD ROW SEAT BELT
SECOND ROW SEAT BELT
FRONT SEAT BELT
SECOND ROW CHILD SEAT
TETHER ANCHOR
page 23-8
step 1 on page 23-13
Inspection, page 23-15
step 1 on page 23-14
page 23-4
step 1 on page 23-10
step 1 on page 23-6
Installation-’99-00 models, page 23-16
Removal and Installation-’01-04 models, page 23-17
Replacement, page 23-11
Inspection, page 23-15
Replacement, page 23-8
Inspection, page 23-15
Replacement, page 23-4
Inspection, page 23-15
Installation-’99-00 models,
page 23-16
03/07/29 10:30:33 61S0X050_230_0003
01
*01
*02
S0X4A00H46200053401KBAT00
Front Seat Belt
23-4
Seat Belts
Front Seat Belt Replacement
A
B
7/16-20 UNF
32 N·m (3.3 kgf·m, 24 lbf·ft)
A
A
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
B
C
D
SRS components are located in this area. Review the
SRS component locations, ’99-01 models (see page 23-
18), ’02 model (see page 23-19), ’03-04 models (see
page 23-20), and the precautions and procedures (see
page 23-21) before preforming repairs or service.
NOTE: Check the front seat belts for damage, and
replace them if necessary.
1. Make sure you have the anti-theft code for the radio
and the navigation system, and then write down
the frequencies for the preset buttons.
2. Slide the front seat forward fully.
3. Disconnect the negative cable from the battery, and
wait at least 3 minutes before beginning work.
4. Remove the upper anchor cover (A).
5. For ’99-02 models driver’s and passenger’s seat
belts and ’03-04 models driver’s seat belt: Pull the
lower anchor cover (A) back, and remove the lower
anchor bolt (B).
6. For ’03-04 models passenger’s seat belt: Remove
the rear riser cover (see step 7 on page 20-82).
Remove the bolt (A), and release the hook (B), then
remove the lower anchor bracket (C) from the outer
weight sensor (D).
03/07/29 10:30:33 61S0X050_230_0004
04
05
03
’03-04 models passenger’s seat belt
23-5
C
6 x 1.0 mm
4 N·m
(0.4 kgf·m, 3 lbf·ft)
B
F
E
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
G
C
6 x 1.0 mm
4 N·m
(0.4 kgf·m,
3 lbf·ft)
B
F
E
D
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
G
A
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
7. Remove the center pillar lower trim panel (see page
20-58).
8. Remove the upper anchor bolt (A).
9. Disconnect the seat belt tensioner connector (B).
Remove the retractor mounting ET screw (C), and
for ’03-04 models passenger’s seat belt, remove the
retractor bolt (D), then remove the front seat belt (E)
and retractor (F).
10. If necessary, remove the front seat belt protector
(G).
11. Remove the center pillar upper trim (see page 20-
58).
12. Remove the shoulder anchor adjuster (A).
13. Install the seat belt and retractor in the reverse
order of removal, and note these items:
• Apply liquid thread lock to the anchor bolts
before reinstallation.
• Check that the retractor locking mechanism
functions (see page 23-15).
• Assemble the washers, collar and bushing on the
upper and lower anchor bolts as shown.
• If the seat belt tensioner has been activated,
replace the front seat belt protector with a new
one.
• Before installing the anchor bolts, make sure
there are no twists or kinks in the seat belt.
• Make sure the seat belt tensioner connector is
plugged in properly.
• Reconnect the negative cable to the battery.
• Enter the anti-theft code for the radio and the
navigation system, and then enter the customer’s
radio station presets.
• Reset the clock.
• Do the PCM idle learn procedure (see page 11-
202) and the power window control unit reset
procedure (’03-04 models) (see page 22-200).
(cont’d)
03/07/29 10:30:34 61S0X050_230_0005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст