Honda Odyssey 2004. Manual — part 543
−
−
−
−
04
05
*01
07
YES
NO
YES
NO
23-114
SRS
DTC Troubleshooting (cont’d)
A
SRS UNIT CONNECTOR A (18P)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the special tool from the SRS main
harness 4P connector.
14. Check resistance between the No. 4 and No. 13
terminals and between the No. 5 and No.14
terminals of SRS unit connector A (18P). There
should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 15.
15. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
16. Check resistance between the No. 7 and the No. 8
terminals and between the No. 1 and the No. 2
terminals of the SRS main harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS floor harness; replace the
SRS floor harness.
Short in the SRS main harness; replace the
SRS main harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:34:34 61S0X050_230_0114
−
−
−
−
01
02
03
S0X4AZ3K79100081024FAAT00
’02 Model
DTC 2-4:
Special Tools Required
YES
NO
YES
NO
23-115
A
07XAZ-SZ30100
07SAZ-TB4011A
A
B
A
B
Short to Power in Front Passenger’s
Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the SRS main harness 4P connector
(A).
5. Connect the special tool (2
connectors) to the
SRS main harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the front passenger’s airbag
inflator; replace the front passenger’s airbag (see
page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 4P connector (A)
from the cable reel 4P connector (B).
11. Disconnect both seat belt tensioner 2P connectors
(A) from the side wire harness 2P connectors (B).
(cont’d)
Does the SRS indicator stay on?
Is DT C 2-4 indicated?
03/07/29 10:34:35 61S0X050_230_0115
−
−
−
−
04
05
*01
07
YES
NO
YES
NO
23-116
SRS
DTC Troubleshooting (cont’d)
A
SRS UNIT CONNECTOR A (18P)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the special tool from the SRS main
harness 4P connector.
14. Reconnect the battery negative cable.
15. Turn the ignition switch ON (II).
16. Check for voltage between the No. 4 terminal of
SRS unit connector A (18P) and body ground, the
No. 13 terminal and body ground, the No. 5
terminal and body ground, and the No. 14 terminal
and body ground. There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 17.
17. Turn the ignition switch OFF.
18. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
19. Turn the ignition switch ON (II).
20. Check for voltage between the No. 7 terminal of the
SRS main harness 28P connector and body ground,
the No. 8 terminal and body ground, the No. 1
terminal and body ground, and the No. 2 terminal
and body ground. There should be 0.5 V or less.
Short to power in the SRS floor harness;
replace the SRS floor harness.
Short to power in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Wire side of female terminals
Is the voltage as specif ied?
Is the voltage as specif ied?
03/07/29 10:34:35 61S0X050_230_0116
−
−
−
−
01
02
03
S0X4AZ3K79100081025FAAT00
’02 Model
DTC 2-5:
Special Tools Required
YES
NO
YES
NO
23-117
A
07XAZ-SZ30100
07SAZ-TB4011A
A
B
A
B
Short to Ground in Front Passenger’s
Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the SRS main harness 4P
connector (A).
5. Connect the special tool (2
connectors) to the
SRS main harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to ground in the front passenger’s
airbag inflator; replace the front passenger’s airbag
(see page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 4P connector (A)
from the cable reel 4P connector (B).
11. Disconnect both seat belt tensioner 2P connectors
(A) from the side wire harness 2P connectors (B).
(cont’d)
Does the SRS indicator stay on?
Is DT C 2-5 indicated?
03/07/29 10:34:36 61S0X050_230_0117
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст