Honda Odyssey 2004. Manual — part 443
01
S0X4A00J22100030051KBAT01
S0X4A00J26300039801LBAT02
How to Reset
Blinking Pattern:
Miles (km)
Maintenance Reminder Light
22-100
22-100
Gauges
Gauge Assembly Replacement
D
B
A
C
1. Remove the instrument panel (see page 20-69).
2. Remove the screws (A) from the gauge assembly
(B), and spread a protective cloth (C) on the upper
column cover.
3. Disconnect the connectors (D), and remove the
gauge assembly.
4. Install in the reverse order of removal.
Press the select switch and reset switch at the same
time, turn the ignition switch ON (II), and hold them
more than 10 seconds.
At 5,900 (9,440)
to 6,100 (9,760)
Blinks for 10 seconds when
the ignition switch is turned
ON (II).
At 7,400 (11,840)
to 7,600 (12,160)
Comes on and stays on while
the ignition switch is ON (II).
03/07/29 10:21:03 61S0X050_220_0102
Indicator
Resetting the Maintenance Required
−
−
−
−
01
02
01
S0X4A00J22170863203FAAT00
Before testing
YES
NO
Except ’01 model:
’01 model:
YES
NO
22-101
Vehicle Speed Signal Circuit Troubleshooting
GAUGE ASSEMBLY CONNECTOR B (22P)
BLU/WHT
PCM CONNECTOR A (32P) (Connected)
BLU/WHT
BLU/WHT
PCM CONNECTOR E (31P) (Connected)
• Check to see if diagnostic trouble code P0720 (9) is
indicated. If it is, troubleshoot the DTC (see page 14-
321).
• Inspect the No. 9 (10A) fuse in the driver’s under-dash
fuse/relay box.
• Check for continuity between the B16 terminal and
body ground (G503).
1. Raise the vehicle, and make sure it is securely
supported.
2. Disconnect the connector B (22P) from the gauge
assembly.
3. Connect the B2 terminal to the positive probe of a
voltmeter, and connect the negative probe to body
ground. To prevent damage to the gauge assembly,
lay the gauge assembly on a shop rag.
4. Put the vehicle in neutral position with the ignition
switch ON (II).
5. Slowly rotate (over 3 mph (2 km/h)) one wheel with
the other wheel blocked.
Substitute a known-good gauge assembly. If
the problem is gone, replace the gauge
assembly.
Go to step 6.
6. Turn the ignition switch off.
7. Connect the No. 9 terminal of the PCM connector A
(32P) (except ’01 model) or the No. 26 terminal of
the PCM connector E (31P) (’01 model) to the
positive probe of a voltmeter, and connect the
negative probe to body ground.
8. Turn the ignition switch ON (II).
9. Slowly rotate (over 3 mph (2 km/h)) one wheel with
the other wheel blocked.
Repair open in the BLU/WHT wire between
the PCM and the gauge assembly.
Go to step 10.
10. Turn the ignition switch OFF.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of
female terminals
Does voltage pulse f r om 0 to appr ox. 5 V or mor e?
Does voltage pulse f r om 0 to appr ox. 5 V or mor e?
03/07/29 10:21:03 61S0X050_220_0103
−
−
01
02
Except ’01 model:
’01 model:
YES
NO
22-102
Gauges
Vehicle Speed Signal Circuit Troubleshooting (cont’d)
PCM CONNECTOR A (32P) (Connected)
BLU/WHT
BLU/WHT
PCM CONNECTOR E (31P) (Disconnected)
11. Disconnect the PCM connector A (32P) (except ’01
model) or E (31P) (’01 model).
12. Disconnect the driver’s multiplex control unit
connector B, and the cruise control unit.
On EX and EXL models: disconnect the left and
right power sliding door control units.
13. Check for continuity between PCM connector A
No. 9 terminal or PCM connector E No. 26 terminal
and body ground.
Repair short to ground in the BLU/WHT wire
between the PCM and the gauge assembly, the
cruise control unit, or the driver’s multiplex control
unit.
Check for these problems:
• Bent, loose or corroded terminals.
• A faulty PCM.
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
03/07/29 10:21:04 61S0X050_220_0104
*01
S0X4A00J26370100000DAAT00
22-103
Safety Indicator System
Component Location Index
FRONT PASSENGER’S DOOR SWITCH
RIGHT REAR DOOR SWITCH
TAILGATE LATCH
SWITCH
BRAKE LIGHT FAILURE SENSOR
LEFT REAR DOOR SWITCH
DRIVER’S DOOR SWITCH
BRAKE PEDAL POSITION SWITCH
SAFETY INDICATOR
Test, page 22-148
Test, page 22-108
Test, page 19-6
Pedal Height Adjustment,
page 19-6
Input Test, page 22-106
03/07/29 10:21:05 61S0X050_220_0105
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст