Honda Odyssey 2004. Manual — part 611
01
02
S0X4ASHH46400043771KBAT00
Removal (’02-04 Models)
Installation (’02-04 Models)
23-387
OPDS Unit Replacement
B
A
A
NOTE: Review the seat replacement procedure before
performing repair or service.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Disconnect the side airbag harness 2P connector
(see step 4 on page 23-31).
3. Remove the seat assembly (see page 20-81) and
seat-back cover (see page 20-102).
4. Disconnect the OPDS unit harness 8P connector
and sensor connectors from the OPDS unit.
5. Remove the two screws (A) and the OPDS unit (B).
1. Place the new OPDS unit on the seat-back frame.
Tighten the two screws (A), and connect the OPDS
unit harness 8P connector and sensor connectors
to the OPDS unit.
2. Install the seat-back cover (see page 20-102).
3. Install the seat assembly (see page 20-81), then
connect the side airbag harness 2P connector.
4. Reconnect the battery negative cable.
5. Set the seat-back in the normal position, and make
sure there is nothing on the front passenger’s seat.
6. Initialize the OPDS unit.
• ’02 Model (see page 23-40)
• ’03-04 Models (see page 23-41)
7. Calibrate the front passenger’s weight sensors unit
(’03-04 Models) (see page 23-42).
8. After installing the OPDS unit, confirm proper
system operation: Turn the ignition switch ON (II);
the SRS indicator should come on for about 6
seconds and then go off.
03/07/29 10:42:57 61S0X050_230_0387
01
02
S0X4A0BH46400027195KBAT00
Removal (’02 Model)
Installation (’02 Model)
23-388
SRS
Front Impact Sensor Replacement
C
A
B
C
B
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
NOTE:
• Removal of the front impact sensor must be
performed according to the precautions/procedures.
• Before disconnecting the front impact sensor 2P
connector(s), disconnect the driver’s and front
passenger’s airbag 4P connectors, and both seat belt
tensioner 2P connector(s).
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
impact sensor.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the front bumper (see page 20-128).
3. Disconnect the side wire harness 2P connector (A),
and remove the two Torx bolts (B) using a Torx T30
bit, then remove the front impact sensor (C).
NOTE:
• Be sure to install the harness wires so they are not
pinched or interfering with other parts.
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
impact sensor.
1. Install the new front impact sensor with new Torx
bolts (A), then connect the engine compartment
wire harness 2P connector (B) to the front impact
sensor (C).
2. Reconnect the battery negative cable.
3. After installing the front impact sensor, confirm
proper system operation: Turn the ignition switch
ON (II): the SRS indicator should come on for about
6 seconds and then go off.
03/07/29 10:42:58 61S0X050_230_0388
01
02
S0X4AZBH46400027195KBAT00
Removal (’03-04 Models)
Installation (’03-04 Models)
23-389
B
C
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
C
B
NOTE:
• Removal of the front sensor must be performed
according to the precautions/procedures.
• Before disconnecting the front sensor 2P connector(s),
disconnect the driver’s and front passenger’s airbag
4P connectors, and both seat belt tensioner 2P
connector(s).
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
sensor.
1. Remove the battery, and wait at least 3 minutes
before beginning work.
2. Disconnect the evaporative emissions canister
hose.
3. Disconnect the engine compartment wire harness
2P connector (A), and remove the two Torx bolts (B)
using a Torx T30 bit, then remove the front
sensor (C).
NOTE:
• Be sure to install the harness wires so they are not
pinched or interfering with other parts.
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
sensor.
1. Install the new front sensor with new Torx bolts (A),
then connect the engine compartment wire harness
2P connector (B) to the front sensor (C).
2. Reconnect the battery negative cable.
3. After installing the front sensor, confirm proper
system operation: Turn the ignition switch ON (II):
the SRS indicator should come on for about 6
seconds and then go off.
03/07/29 10:42:58 61S0X050_230_0389
01
02
S0X4AZBH46400053795KBAT00
Removal (’03-04 Models)
Installation (’03-04 Models)
23-390
SRS
Front Passenger’s Weight Sensor Replacement
A
B
32 N·m
(3.3 kgf·m,
24 lbf·ft)
A
NOTE:
• Removal of the front passenger’s weight sensors
must be performed according to the precautions/
procedures described at the beginning of this section.
• Before disconnecting the front passenger’s weight
sensors connectors, disconnect the front passenger’s
airbag 4P connector..
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
passenger’s weight sensors.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the seat assembly (see page 20-81) and
seat riser (see page 20-99).
3. Disconnect the front passenger’s weight sensors
connectors from the seat weight sensor unit (see
page 23-391).
4. Remove the harness clips and mounting nuts (A),
then remove the front passenger’s weight sensors
(B) from the seat riser.
NOTE:
• Be sure to install the harness wires so they are not
pinched or interfering with other parts.
• Do not turn the ignition switch ON (II), and do not
connect the battery cable while replacing the front
passenger’s weight sensors.
• Tighten the mounting nuts from the backside.
Improper tightening could cause the airbag system to
accidentally deploy, causing damage or injuries.
1. Place the new front passenger’s weight sensors on
the seat riser. Tighten the mounting nuts (A) from
the backside and connect the sensor connectors to
the front passenger’s weight sensors unit. Then
install the harness clips.
2. Install the seat riser (see page 20-99) and the seat
assembly (see page 20-81).
3. Reconnect the battery negative cable.
4. Calibrate the front passenger’s weight sensors unit
(see page 23-42).
5. After installing the front passenger’s weight
sensors, confirm proper system operation: Turn the
ignition switch ON (II): the SRS indicator should
come on for about 6 seconds and then go off.
03/07/29 10:42:59 61S0X050_230_0390
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст