Honda Odyssey 2004. Manual — part 369
26
27
20-118
Seats
Second Row Seat Cover Replacement - Bench-type (cont’d)
B
A
A
B
5. Pull back the edge of the seat cushion cover all the
way around, and release the clips (A), then remove
the seat cushion cover (B).
6. Install the cover in the reverse order of removal,
and note these items:
• To prevent wrinkles when installing a seat
cushion cover, make sure the material is
stretched evenly over the pad before securing
the clips and hooks.
• Replace any clips you removed with new ones
(A) using commercially available upholstery ring
pliers (B).
03/07/29 10:03:25 61S0X050_200_0120
01
S0X4A00J46173853904KDAT00
20-119
Third Row Seat Removal/Installation
A
A
PIVOT BEARING
PIVOT BUSHING
PIVOT BRACKET
PIVOT BUSHING
SPRING PINS
B
B
C
THIRD ROW SEAT
A
A
THIRD ROW SEAT STRIKER
Fastener Locations
: Bolt, 4
: Bolt, 4
: Bolt, 2
: Nut, 4
7/16-20 UNF
47 N·m
(4.7 kgf·m,
35 lbf·ft)
12 x 1.25 mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
14 x 1.5 mm
44 N·m
(4.5 kgf·m,
33 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
B
C
NOTE: Take care not to scratch the interior trim and body or tear the seat covers.
1. Remove the third row seat as shown.
2. Install the seat in the reverse order of removal and note these items:
• After disassembling the pivot bracket, replace the pivot bushings.
• Make sure the third row seat latches and unlatches properly, and if necessary, adjust the third row seat striker
forward or rearward.
Remove the rear side trim panel.
Replace.
Replace.
Replace.
Remove the rear side trim panel.
03/07/29 10:03:26 61S0X050_200_0121
01
01
01
S0X4A00J46173854021KBAT00
20-120
Seats
Third Row Seat-back Recline Lever Replacement
Fastener Locations
: Screw, 2
A
Fastener Location
: Screw, 1
B
A
Fastener Locations
: Screw, 4
A
B
B
A
NOTE:
• Take care not to scratch the interior trim.
• Take care not to tear the seams or damage the seat
covers.
• Take care not to kink the recline cables.
• Put on gloves to protect your hands.
1. Remove the screws, and remove the recline lever
trim (A) from behind the seat-back.
2. Remove the screw and release the hook (A), then
remove the recline upper cover (B) from each side.
3. Remove the seat-back cover, as necessary (see
page 20-124).
4. Remove the screws and disconnect the recline
cables (A) from the recline lever (B), then remove it.
5. Install the lever in the reverse order of removal,
and make sure the recline cables are connected
securely.
03/07/29 10:03:27 61S0X050_200_0122
01
02
01
S0X4A00J46173853651KBAT00
20-121
Third Row Seat Cushion Latch Lever Replacement
Fastener Locations
: Screw, 4
A
Fastener Locations
: Bolt, 6
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
A
B
Fastener Locations
: Screw, 2
B
A
NOTE:
• Take care not to tear the seams or damage the seat
covers.
• Take care not to kink the cushion latch cables.
• Put on gloves to protect your hands.
1. Remove the third row seat through the tailgate
opening (see page 20-119).
2. Remove the screws, then remove the recline cover
(A) from each side.
3. Remove the bolts, then separate the seat-back (A)
and seat cushion (B).
4. Remove the screws and release the hooks (A), then
remove the cushion latch lever trim (B).
(cont’d)
03/07/29 10:03:27 61S0X050_200_0123
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст