Honda Odyssey 2004. Manual — part 596
−
−
−
−
−
−
−
−
01
02
S0X4AZBK791000R921XFAAT20
’03-04 Models
DTC 92-1x (92-10 to 92-19, 92-1A to 92-1F):
YES
NO
YES
NO
YES
NO
YES
NO
23-326
SRS
DTC Troubleshooting (cont’d)
A
DASHBOARD WIRE HARNESS A 4P CONNECTOR
YEL
Open in Passenger Airbag Cutoff Indicator
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Check the connection between the dashboard wire
harness A 4P connector and the passenger’s airbag
cutoff indicator.
4. Erase the DTC memory.
5. Read the DTC (see page 23-38).
Go to step 6.
The system is OK; if DTC 92-1x is still present,
go to step 6.
6. Check the No. 9 (10A) fuse in the driver’s
under-dash fuse/relay box.
Go to step 7.
Replace the fuse, then turn the ignition switch
ON (II). If the fuse blows again, check for a short in
the No. 9 (10A) fuse circuit (dashboard wire
harness A).
7. Disconnect the dashboard wire harness A 4P
connector from the passenger’s airbag cutoff
indicator.
8. Turn the ignition switch ON (II).
9. Check for voltage between the No. 1 terminal of the
dashboard wire harness A 4P connector and body
ground. There should be battery voltage.
Go to step 10.
Open in dashboard wire harness A; replace
dashboard wire harness A.
10. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Wire side of female terminals
Does the passenger air bag cutof f indicator stay
on?
Is DT C 92-1x indicated?
Is the f use OK ?
Is ther e batter y voltage?
03/07/29 10:41:16 61S0X050_230_0326
−
−
03
04
05
06
YES
NO
23-327
A
A
SRS UNIT CONNECTOR A (28P)
RED/BLU
JUMPER
WIRE
A
11. Disconnect SRS unit connector A (28P) from the
SRS unit.
12. Reconnect the dashboard wire harness A 4P
connector to the passenger’s airbag cutoff indicator.
13. Reconnect the battery negative cable.
14. Connect the No. 20 terminal of SRS unit connector
A (28P) to body ground with a jumper wire.
15. Turn the ignition switch ON (II).
16. Check the passenger’s airbag cutoff indicator.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 17.
17. Turn the ignition switch OFF.
18. Disconnect the jumper wire.
19. Disconnect the dashboard wire harness A 4P
connector from the passenger’s airbag cutoff
indicator again.
(cont’d)
Wire side of female terminals
Does the passenger ’s air bag cutof f indicator come
on?
03/07/29 10:41:17 61S0X050_230_0327
−
−
−
−
−
−
07
*01
09
YES
NO
YES
NO
23-328
SRS
DTC Troubleshooting (cont’d)
DASHBOARD WIRE
HARNESS A
4P CONNECTOR
SRS UNIT CONNECTOR A (28P)
RED/BLU
RED/BLU
C582
A
DASHBOARD WIRE HARNESS A 4P CONNECTOR
SRS FLOOR SUBHARNESS
28P CONNECTOR C852
RED/BLU
RED/BLU
20. Check resistance between the No. 4 terminal of the
dashboard wire harness A 4P connector and the
No. 20 terminal of SRS unit connector A (28P).
There should be 0
1.0
.
Faulty passenger’s airbag cutoff indicator;
replace the passenger’s airbag cutoff indicator.
Go to step 21.
21. Disconnect SRS floor subharness 28P connector (A)
from the SRS floor harness connector C582.
22. Check resistance between the No. 4 terminal of the
dashboard wire harness A 4P connector and the
No. 6 terminal of SRS floor subharness 28P
connector C852. There should be 0
1.0
.
Open in the SRS floor harness; replace the
SRS floor harness.
Go to step 23.
23. Disconnect left side wire harness 3P connector
C558 from the SRS floor subharness.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:41:17 61S0X050_230_0328
−
−
−
−
−
−
10
*02
YES
NO
YES
NO
23-329
DASHBOARD WIRE
HARNESS A
4P CONNECTOR
RIGHT SIDE
WIRE HARNESS
3P CONNECTOR C558
RED/BLU
RED/BLU
DASHBOARD WIRE HARNESS A 4P CONNECTOR
RED/BLU
RED/BLU
DASHBOARD WIRE HARNESS A
21P CONNECTOR C501
24. Check resistance between the No. 4 terminal of the
dashboard wire harness A 4P connector and the
No. 1 terminal of right side wire harness 3P
connector C558. There should be 0
1.0
.
Open in the SRS floor subharness; replace
the SRS floor subharness.
Go to step 25.
25. Disconnect dashboard wire harness A 21P
connector C501 from the left side wire harness.
26. Check resistance between the No. 4 terminal of the
dashboard wire harness A 4P connector and the
No. 4 terminal of dashboard wire harness A 21P
connector C501. There should be 0
1.0
.
Open in the left side wire harness; replace
the left side wire harness.
Open in dashboard wire harness A; replace
dashboard wire harness A.
Wire side of female terminals
Terminal side of female terminals
Wire side of
female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:41:18 61S0X050_230_0329
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст