Honda Odyssey 2004. Manual — part 243
11
01
02
S0X4AA1E10410613041KBAT00
14-366
Automatic Transmission
ATF Temperature Sensor Replacement
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
C
1. Remove the transmission lower mount nuts.
2. Place the transmission jack under the transmission,
and lift it up until the studs of the transmission
lower front mount clear the subframe.
3. Remove the transmission lower front mount.
4. Disconnect the connector (A) from the ATF
temperature sensor.
5. Remove the bolts securing the sensor harness
clamp and ATF temperature sensor, then remove
the ATF temperature sensor (B).
6. Install the new ATF temperature sensor with a new
O-ring (C).
7. Install the harness clamp, then connect the
connector.
8. Install the transmission lower front mount.
9. Lower the transmission, then install the
transmission lower mount nuts.
10. Remove the transmission jack.
03/07/29 09:40:18 61S0X050_140_0369
−
01
*01
01
S0X4AA1E10400013001MAAT00
14-367
ATF Level Check
A
B
C
B
24 x 1.5 mm
44 N·m
(4.5 kgf·m,
33 lbf·ft)
C
A
NOTE: Keep all foreign particles out of the transmission.
1. Warm up the engine to normal operating
temperature (the radiator fan comes on).
2. Park the vehicle on the level ground. Turn off the
engine.
NOTE: Check the fluid level within 60
90 seconds
after turning the engine off.
3. Remove the dipstick (yellow loop) (A) from the
transmission, and wipe it with a clean cloth.
4. Insert the dipstick into the transmission.
5. Remove the dipstick and check the fluid level. It
should be between the upper mark (B) and lower
mark (C).
6. If the level is below the lower mark, check for fluid
leaks at the transmission, hose and line joints. If a
problem is found, fix it before filling the
transmission.
7. If necessary, fill the transmission into the filler hole
(A) to bring the fluid level up to the upper mark.
Always use Honda ATF-Z1 Automatic Transmission
Fluid (ATF). Using a non-Honda ATF can affect shift
quality.
8. If the level is above the upper mark, drain the ATF
to proper level (see step 3 on page 14-368).
9. Install the ATF filler bolt (B) with a new sealing
washer (C).
10. Insert the dipstick back into the transmission.
03/07/29 09:40:19 61S0X050_140_0370
01
02
S0X4AA1E10400013001KBAT00
Automatic Transmission Fluid Capacity:
3.3
(3.5 US qt) at changing
7.9
(8.3 US qt) at overhaul
14-368
Automatic Transmission
ATF Replacement
A
18 x 1.5 mm
49 N·m (5.0 kgf·m,
36 lbf·ft)
B
B
24 x 1.5 mm
44 N·m
(4.5 kgf·m,
33 lbf·ft)
C
A
NOTE: Keep all foreign particles out of the transmission.
1. Bring the transmission up to operating temperature
(the radiator fan comes on) by driving the vehicle.
2. Park the vehicle on the level ground, and turn the
engine off.
3. Remove the ATF filler bolt and the drain plug (A),
and drain the automatic transmission fluid (ATF).
NOTE: If a cooler flusher is used, refer to ATF
Cooler Flushing (see page 14-388).
4. Reinstall the drain plug with a new sealing washer
(B).
5. Refill the transmission with the recommended fluid
into the filler hole (A) to the upper mark on the
dipstick. Always use Honda ATF-Z1 Automatic
Transmission Fluid (ATF). Using a non-Honda ATF
can affect shift quality.
6. Install the ATF filler bolt (B) with a new sealing
washer (C).
03/07/29 09:40:20 61S0X050_140_0371
01
13
02
S0X4AA1E10410400000KAAT00
Special Tools Required
14-369
Transmission Removal
A
18 x 1.5 mm
49 N·m (5.0 kgf·m,
36 lbf·ft)
B
A
B
C
• Engine support hanger 07XAA-001030A
• Engine hanger balance bar VSB02C000019
• Subframe adapter EQS07AODSY0
(Available through the Honda Tool and Equipment
Program, 888-424-6857)
1. Before disconnecting the battery, make sure you
have the anti-theft code for the radio, then write
down the frequencies for the radio’s preset stations.
2. Remove the bolt securing the lower portion of the
windshield washer reservoir opening. Remove the
support rod, then fix the hood in a vertical position
using the support rod.
3. Remove the engine covers.
4. Remove the intake air duct, resonator cover, and air
cleaner housing assembly.
5. Disconnect the battery negative terminal, then
remove the battery positive terminal.
6. Remove the battery hold-down bracket, then
remove the battery and battery tray.
7. Remove the battery cable clamps, connector, and
relay bracket from the battery base.
8. Remove the battery base.
9. Raise the vehicle, and make sure it is securely
supported.
10. Remove the splash shield.
11. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF). Reinstall the drain plug
and a new sealing washer (B).
12. Remove the breather tube (A) from its clamp (B) on
the radiator hose (C).
(cont’d)
03/07/29 09:40:20 61S0X050_140_0372
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст