Honda Odyssey 2004. Manual — part 286
08
01
10
11
17-32
Power Steering
Steering Gearbox Removal (cont’d)
C
A
B
C
B
C
C
C
A
30 mm (1.18 in.)
A
A
A
A
17. Pass the removed 12 mm flange bolt (A) through
the bolt hole of the mounting bracket (B), and hook
the rear engine mount (C) removed in step 16 on
the 12 mm flange bolt.
18. Attach a wood block (A) to the lower center of the
front subframe (B). Attach a jack to the center of the
wood block and support the front subframe
securely by raising the jack.
19. Loosen the four 14 mm special bolts (C) on the
front subframe so they are 30 mm (1.18 in.) from
the mounting surface (until the stepped part of
each bolt can be seen). Do not loosen the 14 mm
special bolts more than necessary.
20. Remove the four 12 mm flange bolts from the front
stiffener plates (A).
21. Remove the two 12 mm flange bolts from the rear
stiffener plates (A).
03/07/29 09:49:31 61S0X050_170_0032
12
13
14
15
17-33
A
B
A
22. Lower the jack slowly until the front subframe is
held with the 14 mm special bolts that were
loosened in step 19.
23. Remove the clamp for the feed line (A) from the
right mounting bracket (B) of the steering gearbox.
24. Remove the two 10 mm mounting bolts from the
left gearbox.
25. Move the steering gearbox (A) between the body
and front subframe toward the left, and remove the
steering gearbox.
03/07/29 09:49:32 61S0X050_170_0033
*01
S0X4A00F00000057111LAAT00
Exploded View
17-34
Power Steering
Steering Gearbox Overhaul
O-RING
CYLINDER END SEAL
FLARE NUTS
13 N·m (1.3 kgf·m, 9.4 lbf·ft)
CYLINDER LINE B
CYLINDER LINE A
FLANGE BOLTS
18 N·m (1.8 kgf·m, 13 lbf·ft)
VALVE BODY UNIT
GASKET
LOCKNUT
RACK GUIDE SCREW
SPRING
RACK GUIDE
END PLUG
59 N·m (6.0 kgf·m, 43 lbf·ft)
NUT
25 N·m (2.5 kgf·m, 18 lbf·ft)
GEARBOX HOUSING
FLARE NUTS
13 N·m (1.3 kgf·m, 9.4 lbf·ft)
O-RINGS
RACK STOP
CYLINDER END SEAL
O-RING
PISTON SEAL RING
O-RING
RACK BUSHING
CIRCLIP
STEERING RACK
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
03/07/29 09:49:33 61S0X050_170_0034
02
*16
04
Special Tools Required
Removal
Disassembly
17-35
B
A
A
A
B
C
D
E
• Cylinder end seal remover attachment
07TAF-SZ50100
• Driver 07749-0010000
• Attachment, 42 x 47 mm 07746-0010300
• Piston seal ring guide
07LAG-SM4010A or 07LAG-SM40100
• Piston seal ring sizing tool
07LAG-SM4020A or 07LAG-SM40200
• Pincer Oetiker 1098, or equivalent,
commercially available
NOTE: Refer to the Exploded View as needed during the
following procedure.
1. Remove the steering gearbox (see page 17-30).
2. Remove the boot band (A) and tie-rod clips (B). Pull
the boots away from the ends of the steering
gearbox.
3. Unbend the lock washer (A).
4. Hold the flat surface sections (A) on the right side
steering rack (B) with a wrench, and unscrew the
both rack ends (C) with another wrench. Be careful
not to damage the rack surface with the wrench.
Remove the lock washer (D) and stop washer (E).
(cont’d)
03/07/29 09:49:34 61S0X050_170_0035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст