Honda Accord Hybrid (2022 year). Manual in english — page 26
415
Driving
Towing a Trailer
Your vehicle is not designed to tow a trailer. Attempting to do so can void your
warranties.
Towing Behind a Motorhome
Your vehicle is not designed to be towed behind a motor home. If your vehicle needs
to be towed in an emergency, refer to the emergency towing information.
2
416
Driving
When Driving
Turning on the Power
1.
Make sure the parking brake is applied.
u
The parking brake and brake system
indicator (red) comes on for 30 seconds
when you pull up the electric parking
brake switch.
2.
Depress the brake pedal.
1
Keep your foot firmly on the brake pedal when
starting the power system.
The engine is harder to start in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
meters).
When turning on the power system in cold weather,
turn off all electrical accessories such as the lights,
climate control system, and rear defogger in order to
reduce the 12-volt battery drain.
If you live in a region where winter is extremely cold,
an engine block heater will improve starting and
warming of the engine. Consult a dealer for details.
If the exhaust system sounds abnormal or you can
smell exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
Electric Parking Brake Switch
Brake Pedal
Continued
417
uu
When Driving
u
Turning on the Power
Driving
3.
Without depressing the accelerator pedal,
press the
POWER
button while depressing
the brake pedal.
4.
Check the
READY
indicator.
u
Keep depressing the brake pedal until
the
READY
indicator comes on.
u
The
READY
indicator comes on when
the power system is on and you can start
driving.
u
If the outside temperature is extremely
low, you cannot drive until conditions are
improved. In this case, the
READY
indicator does not come on and a
warning message appears on the driver
information interface.
2
Driver Information Interface
Warning and Information Messages
P. 115
1
The immobilizer system protects your vehicle from
theft. If an improperly coded device is used, the
power system does not activate.
2
P. 190
When you set the power mode to ON, you may feel
the brake pedal slightly sink down. This is normal.
Bring the keyless remote close to the
POWER
button
if the battery in the keyless remote is weak.
2
If the Keyless Remote Battery is Weak
P. 602
The power system may not activate if the keyless
remote is subjected to strong radio waves.
Do not hold the
POWER
button to start the power
system.
If the power system does not start, wait at least 30
seconds before trying again.
The engine may not run when the vehicle is ready for
driving.
You can start driving with the
READY
indicator on.
If you press the
POWER
button while depressing the
brake pedal with the
READY
indicator on, the power
mode is set to VEHICLE OFF and you cannot start
driving.
2
P. 94
uu
When Driving
u
Turning on the Power
418
Driving
You can remotely turn the power system on using the keyless remote.
■
To turn the power system on
The power system is on for up to 10 minutes without you starting the vehicle.
To extend the time for another 10 minutes during the first 10 minutes, press the
button, then press and hold the
button.
u
Some exterior lights flash six times if a 10-minute extension request was
transmitted successfully.
■
Remote Engine Start
1
The remote engine start may violate local laws.
Before using the remote engine start, check your
local laws.
If there are buildings and obstacles between your
vehicle and the remote, the range will be reduced.
This distance may vary by external electrical
interference.
3
WARNING
Carbon monoxide gas is toxic and can
rapidly accumulate in closed or even partly
enclosed areas.
Breathing it can cause unconsciousness and
even kill you.
Never use the remote engine starter with
the vehicle parked in a garage or other
areas with limited ventilation.
Press the
button, then press and
hold the
button.
Some exterior lights flash once.
Go within the range,
and try again.
LED: Blinks when any button is pressed.
Some exterior lights flash six
times if the power system
turns on successfully.
Exterior lights will not flash if
the power system turns on
unsuccessfully.
Continued
419
uu
When Driving
u
Turning on the Power
Driving
■
To turn the power system off
1
The power system may not be turned on by the
remote engine start if:
•
You have disabled a remote engine start setting
using the audio/information screen.
2
•
The power mode is not in VEHICLE OFF.
•
The transmission is in a position other than
(
P
.
•
The hood is open, or any door or the trunk is unlocked.
•
You have already used the remote twice to turn the
power system on.
•
Another registered keyless remote is in the vehicle.
•
There is an antenna failure.
•
The door is unlocked with the built-in key.
•
The engine oil pressure is low.
•
The engine coolant temperature is extremely high.
•
The telematics unit
*
malfunctions.
•
The security system alarm is not set.
The power system may be turned off while it is on if:
•
You do not start the vehicle within 10 minutes of
turning the power system on with the keyless
remote.
•
The power system is turned off by using the keyless
remote.
•
The security system alarm is activated.
•
The door is unlocked with the built-in key.
•
The hood is open.
•
The engine coolant temperature is extremely high.
•
The engine oil pressure is low.
•
The malfunction indicator lamp comes on if there is
a problem with the emissions control systems.
•
The transmission is in a position other than
(
P
.
Press and hold
the
button
for one second.
Go within the range,
and try again.
The exterior lights flash once if the power system turns off
successfully.
The exterior lights will not flash when the remote is out of
the keyless access system range.
The power system will not be turned off.
* Not available on all models
uu
When Driving
u
Turning on the Power
420
Driving
1
While the power system is on, the vehicle will
automatically precondition inside the vehicle.
When it is warm outside:
•
The climate control system is activated in auto
mode.
When it is cold outside:
•
The defroster is activated at a moderately warm
temperature.
•
The rear defogger and door mirror heaters are
activated.
•
The seat heaters
*
and heated steering wheel
*
are
activated.
2
2
2
Front Seat Heaters and Seat Ventilation
P. 242
* Not available on all models
421
uu
When Driving
u
Turning on the Power
Driving
1.
Depress and hold the brake pedal, then press the
POWER
button.
2.
Keeping your right foot on the brake pedal, check that the
READY
indicator is on,
then put the transmission into
(
D
. Select
(
R
when reversing.
3.
With the parking brake applied, release the brake pedal and gently depress the
accelerator pedal.
u
Make sure the parking brake and brake system indicator (red) goes off.
2
■
Hill start assist system
Hill start assist keeps the brake engaged briefly to help prevent the vehicle from
rolling on inclines as you move your foot from the brake pedal to the accelerator.
Put the transmission into
(
D
when facing uphill, or
(
R
when facing downhill, then
release the brake pedal.
You can turn the power system off when the vehicle is completely stopped.
1.
Put the transmission into
(
P
.
2.
Press the
POWER
button.
■
Starting to Drive
■
Stopping the Power System
1
You can also release the parking brake by pressing
the electric parking brake switch while depressing the
brake pedal.
When facing downhill, you can start your vehicle
more smoothly by manually releasing it with the
electric parking brake switch than by releasing it with
the accelerator pedal.
The power system is off when the transmission is
taken out of
(
P
before the
POWER
button is
pressed. Follow the step 1 when starting to drive.
As a hybrid vehicle, the sounds and vibrations from
the engine may be absent even though the vehicle is
ready for driving. It also makes you fail to recognize
that you can start.
Make sure to check if the
READY
indicator is on
before you start to drive.
When the power system is turned on using the
button on the keyless remote
When the power system is turned on using the
button on the keyless remote
When the power system is turned on in any case
1
Hill start assist may not prevent the vehicle from
rolling downhill on a very steep or slippery slope, and
does not operate on small inclines.
Hill start assist is not a replacement for the parking
brake.
422
uu
When Driving
u
Precautions While Driving
Driving
Precautions While Driving
Avoid driving in deep water and on flooded roads. This can damage the power
system or driveline, or cause electrical component failure.
If there is a strong impact with something under the vehicle, stop in a safe location.
Check the underside of the vehicle for damage or any fluid leaks.
Transmission
As with a conventional gasoline-powered vehicle with an automatic transmission,
this vehicle will creep.
Keep the brake pedal firmly depressed when stopped.
■
In Rain
■
Other Precautions
■
Creeping
1
NOTICE
Do not change the shift position while pressing the
accelerator pedal. You could damage the
transmission.
NOTICE
If you repeatedly turn the steering wheel at an
extremely low speed, or hold the steering wheel in
the full left or right position for a while, the electric
power steering (EPS) system heats up. The system
goes into a protective mode, and limits its
performance. The steering wheel becomes harder
and harder to operate. Once the system cools down,
the EPS system is restored.
Repeated operation under these conditions can
eventually damage the system.
If the power mode is set to ACCESSORY while
driving, the power system will shut down and all
steering and brake power assist functions will stop,
making it difficult to control the vehicle.
Do not select
(
N
while driving as you will lose
regenerative braking (and acceleration) performance.
During the first 600 miles (1,000 km) of operation,
avoid sudden acceleration or full throttle operation so
as not to damage the power system or powertrain.
Avoid hard braking for the first 200 miles (300 km)
after purchasing your new vehicle or replacing the
brake pads or rotors, to allow for proper break-in.
423
uu
When Driving
u
Shifting
Continued
Driving
Shifting
Change the shift position in accordance with your driving needs.
■
Shift button positions
1
While the High Voltage battery level is full, or the
High Voltage battery temperature is low,
regenerative braking may become less effective.
To prevent malfunction and unintended
engagement:
•
Do not spill any liquids on or around shift buttons.
•
Do not place or drop any objects on or around shift
buttons.
•
Do not let passengers or children operate the shift
buttons.
You may occasionally find that it takes longer than
usual for the vehicle to start moving when you select
(
R
, release the brake pedal, and/or depress the
accelerator pedal. This may occur when the High
Voltage battery level is extremely low, and does not
indicate a vehicle malfunction.
3
WARNING
The vehicle can roll away if left unattended
without confirming that Park is engaged.
A vehicle that rolls away could cause a crash
resulting in serious injury or death.
Always keep your foot on the brake pedal
until you have confirmed that
(
P
is shown
on the shift position indicator.
Park
Used when parking or turning the power
on or off.
Transmission is locked.
Reverse
Used when reversing.
Neutral
Transmission is not locked.
Drive
●
Used for normal driving.
●
The deceleration paddle selector can be
used temporarily.
●
The deceleration paddle selector can be
used when SPORT mode is on.
uu
When Driving
u
Shifting
424
Driving
■
(
P
(parking) button
The shift position changes to
(
P
when you
press the
(
P
button while the vehicle is
parked with the power mode in ON.
The indicators on the sides of the
(
P
button
come on.
1
The beeper sounds and the message appears on the
driver information interface when you depress the
accelerator pedal with the shift position in
(
N
.
2
Driver Information Interface Warning and
Information Messages
P. 115
Change the shift position to
(
D
or
(
R
with the brake
pedal depressed.
When shifting positions in extremely low
temperatures (-22°F/-30°C), there may be a short
delay before the shift position is displayed. Always
confirm you are in the correct shift position before
driving.
(
P
Button
Continued
425
uu
When Driving
u
Shifting
Driving
■
Shift Operation
1
NOTICE
When you change
(
D
to
(
R
and vice versa, come to
a complete stop and keep the brake pedal depressed.
Operating the shift button before the vehicle has
come to a complete standstill can damage the
transmission.
Use the shift position indicator and the shift button
indicator to check the shift position before selecting a
shift button.
If the indicator of the currently selected shift position,
or all the shift position indicators are blinking
simultaneously, there is a problem with the
transmission.
Avoid sudden acceleration and have the transmission
checked by a dealer as soon as possible.
The beeper sounds once when you change to
(
R
.
2
P. 357
Shift Position Indicator
(Transmission System Indicator)
Press the
(
P
button.
Press back the
(
R
button.
Press the
(
N
button.
Press the
(
D
button.
Shift Button
Indicator
Deceleration Paddle Selector
Indicator
uu
When Driving
u
Shifting
426
Driving
■
When opening the driver’s door
If you open the driver’s door under the following conditions, the shift position
automatically changes to
(
P
.
•
The vehicle is stationary with the power mode in ON, or moving at 1 mph (2 km/
h) or slower.
•
The transmission is in other than
(
P
.
•
You have unfastened the driver side seat belt.
u
If you manually change the shift position from
(
P
with the brake pedal
depressed, the shift position will automatically return to
(
P
once you release
the brake pedal.
■
When turning off the power mode
If you turn the power system off while the vehicle is stationary, and the transmission
is in other than
(
P
, the shift position automatically changes to
(
P
.
1
When opening the driver’s door
While the system is designed to automatically change
the shift position to
(
P
under the described
conditions, in the interest of safety you should always
select
(
P
before opening the driver’s door.
Make sure to park the vehicle in a safe place.
2
P. 512
If you want to drive the vehicle after the shift position
has automatically changed to
(
P
under the described
conditions, close the door, fasten the seat belt,
depress the brake pedal, then change the shift
position.
If you leave the vehicle, turn off the power system
and lock the doors.
Continued
427
uu
When Driving
u
Shifting
Driving
■
If you want to keep the transmission in
(
N
position [car wash mode]
With the power system on:
1.
Press and hold the brake pedal.
2.
Press and release the
(
N
button.
u
(
N
(Neutral) hold mode will appear on the driver information interface.
3.
Press the
(
N
button again and hold it for two seconds.
u
The vehicle will enter car wash mode, which must be used when your vehicle
is pulled through a conveyor type automatic car wash where you or an
attendant do not remain in the vehicle.
If you want to cancel car wash mode, select a position other than
(
N
.
If the
POWER
button is pressed after car wash
mode has been activated, the power mode
will change to ACCESSORY and a message
will be displayed on the driver information
interface.
u
For 15 minutes the transmission remains
in
(
N
with the power mode will remain
in ACCESSORY. After that, the
transmission automatically changes to
(
P
and the power mode changes to OFF.
u
Manually changing to
(
P
cancels
ACCESSORY mode. The
(
P
indicator
comes on and the power mode changes
to OFF. You must always put the
transmission into
(
P
when car wash
mode is no longer needed.
1
If you want to keep the transmission in
(
N
position [car wash
mode]
Note that the transmission may not stay in
(
N
position while any of the following indicators is on:
•
Transmission system indicator.
•
Malfunction indicator lamp.
•
Charging system indicator.
428
uu
When Driving
u
Shifting
Driving
■
Restrictions on selecting a shift position
You cannot select a shift position under certain circumstances that may lead to a crash.
When the
transmission is in:
1. Under these circumstances:
2. If you try to change to
the following:
3. The shift position
remains in/changes to:
How to change the
shift position
(
P
The brake pedal is not
depressed.
Other shift position
(
P
Release the accelerator
pedal and depress the
brake pedal.
The accelerator pedal is
depressed.
(
N
The vehicle is moving at low
speed without the brake pedal
depressed.
(
N
The vehicle is moving at low
speed with the accelerator
pedal depressed.
(
N
or
(
D
The vehicle is moving forward.
(
R
Park your vehicle in a
safe place.
(
R
or
(
N
The vehicle is moving backward.
(
D
(
R
,
(
N
, or
(
D
The vehicle is moving.
(
P
(
P
or
(
N
The
READY
indicator is not on.
A shift position other than
(
P
or
(
N
(
P
or
(
N
Make sure that the
READY
indicator
comes on.
429
uu
When Driving
u
SPORT Mode
Driving
SPORT Mode
To turn the SPORT mode on and off, press the
SPORT
button.
The SPORT mode increases engine performance and handling
*
.
This mode is not recommended for fuel economy enhancement, but suitable for
driving on hills or through curves on mountain roads.
The SPORT mode is turned off every time you turn on the power system, even if you
turned it on the last time you drove the vehicle.
SPORT
Button
SPORT
Mode Indicator
Press
Models without adaptive
damper system
Models with adaptive
damper system
* Not available on all models
430
uu
When Driving
u
Deceleration Paddle Selector
Driving
Deceleration Paddle Selector
When you release the accelerator pedal, you can control the rate of deceleration
without removing your hands from the steering wheel. Using the deceleration
paddle selector situated on the steering wheel, you can sequentially shift through
four stages of deceleration.
When descending a hill, you can use the deceleration paddle selector to help
maintain the rate of deceleration, thereby allowing you to keep a safe distance
between your vehicle and the vehicle ahead.
The default deceleration stage is
. Each
paddle selector operation makes a single
stage deceleration change.
u
The deceleration stage may not change if
you keep the paddle selector pulled
back.
To select the different stages of deceleration:
•
Pull back the
(
+
selector (right side) to decrease the deceleration stage.
•
Pull back the
(
-
selector (left side) to increase the deceleration stage.
Pull the
(
+
selector for a few seconds when you want to cancel the deceleration
paddle selector.
1
If you are descending a hill when you select stage
,
the vehicle may enter stage
.
If you pull back right and left paddle selector at the
same time, the deceleration stage may not change.
3
CAUTION
Rapidly increasing the deceleration rate by
quickly shifting the deceleration paddle
selector can cause the tires to skid, resulting
in a crash that could injure or kill someone.
Always maintain a reasonable rate of
deceleration.
Increase
Deceleration
Stage
Decrease
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст