Honda Passport (2022 year). Manual in english — page 35
Continued
557
uu
If a Tire Goes Flat
u
Changing a Flat Tire
Han
d
lin
g the U
n
expected
1.
Put the flat tire in the storage bag provided
with your vehicle.
u
The storage bag is in the tool case.
2.
Knot the top of the storage bag.
3.
Securely put the jack, jack handle bar and
wheel nut wrench back in the tool case.
4.
Bore through the bag, and pass the holding
belt through the hole of the bag and the
wheel of the flat tire as shown.
5.
Place the flat tire in the cargo area, and
thread the belt through the rear anchor as
shown.
6.
Pass the belt through the ring, and tighten
the belt to secure the flat tire in place.
■
Storing the Flat Tire
1
3
WARNING
Loose items can fly around the interior in a
crash and can seriously injure the
occupants.
Store the wheel, jack, and tools securely
before driving.
Belt
Rear Anchor
uu
If a Tire Goes Flat
u
Changing a Flat Tire
558
Han
d
lin
g the U
n
expected
If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator
comes on while you are driving. After driving for a few miles (kilometers), the
indicator will start blinking for a short time and then stay on.
Tire Pressure
Monitor Problem
appears on the driver information interface, but this is normal.
If you replace the tire with a specified regular tire, the warning message on the
driver information interface and the low tire pressure/TPMS indicator will go off after
a few miles (kilometers).
■
TPMS with Tire Fill Assist and the Compact Spare Tire
1
TPMS with Tire Fill Assist and the Compact Spare Tire
The system cannot monitor the pressure of the spare
tire. Manually check the spare tire pressure to be sure
that it is correct.
Use the TPMS specific wheels. Each is equipped with
a tire pressure sensor mounted inside the tire behind
the valve stem.
559
Han
d
lin
g the U
n
expected
Engine Does Not Start
Checking the Engine
If the engine does not start, check the starter.
Starter condition
Checklist
Starter doesn’t turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.
Check for a message on the driver information interface.
●
If the
To Start, Hold Remote Near Start Button
message appears
2
If the Keyless Remote Battery is Weak
P. 560
u
Make sure the keyless remote is in its operating range.
2
ENGINE START/STOP Button Operating Range
The starter turns over normally
but the engine doesn’t start.
There may be a problem with a
fuse. Check each of the items on
the right and respond accordingly.
Review the engine start procedure.
Follow its instructions, and try to start the engine again.
2
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2
Check the fuel level.
There should be enough fuel in the tank.
2
Check the fuses.
Check all fuses, or have the vehicle checked by a dealer.
2
P. 576
If the problem continues:
2
P. 577
1
If you must start the vehicle immediately, use an
assisting vehicle or booster battery to jump start it.
2
P. 562
560
uu
Engine Does Not Start
u
If the Keyless Remote Battery is Weak
Han
d
lin
g the U
n
expected
If the Keyless Remote Battery is Weak
If the beeper sounds, the
To Start, Hold Remote Near Start Button
message
appears on the driver information interface, the
ENGINE START/STOP
button
flashes, and the engine won’t start, start the engine as follows:
1.
Touch the center of the
ENGINE START/
STOP
button with the
H
logo on the keyless
remote while the
ENGINE START/STOP
button is flashing. The buttons on the
keyless remote should be facing you.
u
The
ENGINE START/STOP
button
flashes for about 30 seconds.
2.
Depress the brake pedal and press the
ENGINE START/STOP
button within 10
seconds after the beeper sounds and the
ENGINE START/STOP
button changes
from flashing to on.
u
If you don’t depress the pedal, the mode
will change to ACCESSORY.
561
uu
Engine Does Not Start
u
Emergency Engine Stop
Han
d
lin
g the U
n
expected
Emergency Engine Stop
The
ENGINE START/STOP
button may be used to stop the engine due to an
emergency situation even while driving. If you must stop the engine, do either of the
following operations:
•
Press and hold the
ENGINE START/STOP
button for about two seconds.
•
Firmly press the
ENGINE START/STOP
button three times.
The steering wheel will not lock. However, because turning off the engine disables
the power assist the engine provides to the steering and braking systems, it will
require significantly more physical effort and time to steer and slow the vehicle. Use
both feet on the brake pedal to slow down the vehicle and stop immediately in a
safe place.
The gear position automatically changes to
(
P
after the vehicle comes to a complete
stop. Then, the power mode changes to VEHICLE OFF.
The gear position automatically changes to
(
P
after the vehicle comes to a complete
stop. Then, press the
ENGINE START/STOP
button twice without depressing the
brake pedal to change the mode VEHICLE OFF.
1
Do not press the
ENGINE START/STOP
button while
driving unless it is absolutely necessary for the engine
to be turned off.
If you press the
ENGINE START/STOP
button while
driving, the beeper sounds.
U.S. models
Canadian models
562
Han
d
lin
g the U
n
expected
If the Battery Is Dead
Turn off the power to electric devices, such as audio and lights. Turn off the engine,
then open the hood.
1.
Pull up on the engine compartment cover,
remove it from the pin holders.
2.
Remove the holding clips and the air intake
duct.
■
Jump Starting Procedure
1
Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
Battery performance degrades in cold conditions and
may prevent the engine from starting.
3
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.
Pin
Engine Compartment Cover
Air Intake Duct
Clip
563
uu
If the Battery Is Dead
u
Continued
Han
d
lin
g the U
n
expected
3.
Pull up on the engine cover, remove it from
the pins.
u
Start on the passenger side and lift the
outermost edge of the cover.
u
Move towards the driver side while
applying uniform upward pressure.
4.
Connect the first jumper cable to your
vehicle’s battery
+
terminal.
5.
Connect the other end of the first jumper
cable to the booster battery
+
terminal.
u
Use a 12-volt booster battery only.
u
When using an automotive battery
charger to boost your 12-volt battery,
select a lower charging voltage than 15-
volts. Check the charger manual for the
proper setting.
6.
Connect the second jumper cable to the
booster battery
-
terminal.
7.
Connect the other end of the second
jumper cable to the engine hanger as
shown. Do not connect this jumper cable to
any other part.
8.
If your vehicle is connected to another
vehicle, start the assisting vehicle’s engine
and increase its rpm slightly.
9.
Attempt to start your vehicle’s engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Pin
Engine Cover
Booster Battery
564
uu
If the Battery Is Dead
u
Han
d
lin
g the U
n
expected
Once your vehicle’s engine has started, remove the jumper cables in the following
order:
1.
Disconnect the jumper cable from your vehicle’s ground.
2.
Disconnect the other end of the jumper cable from the booster battery
-
terminal.
3.
Disconnect the jumper cable from your vehicle’s battery
+
terminal.
4.
Disconnect the other end of the jumper cable from the booster battery
+
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
■
What to Do After the Engine Starts
565
Continued
Han
d
lin
g the U
n
expected
Overheating
How to Handle Overheating
Overheating symptoms are as follows:
•
The temperature gauge needle is at the
mark or the engine suddenly loses
power.
•
Stop Driving When Safe. Engine Temperature Too Hot
message appears on
the driver information interface.
•
Steam or spray comes out of the engine compartment.
■
First thing to do
1.
Immediately park the vehicle in a safe place.
2.
Turn off all accessories and turn on the hazard warning lights.
u
No steam or spray present:
Keep the engine running and open the hood.
u
Steam or spray is present:
Turn off the engine and wait until it subsides.
Then, open the hood.
1
NOTICE
Continuing to drive with the temperature gauge
needle at the
mark may damage the engine.
Continuing to drive with the
Stop Driving When
Safe. Engine Temperature Too Hot
message on
the driver information interface may damage the
engine.
3
WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood if steam is coming
out.
H
H
uu
Overheating
u
How to Handle Overheating
566
Han
d
lin
g the U
n
expected
■
Next thing to do
1.
Check that the cooling fan is operating and
stop the engine once the temperature
gauge needle comes down.
u
If the cooling fan is not operating,
immediately stop the engine.
2.
Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks.
u
If the coolant level in the reserve tank is
low, remove the engine compartment
cover then add coolant until it reaches
the
MAX
mark.
2
u
If there is no coolant in the reserve tank,
check that the radiator is cool. Cover the
radiator cap with a heavy cloth and open
the cap. If necessary, add coolant up to
the base of the filler neck, and put the
cap back on.
■
Last thing to do
Once the engine has cooled sufficiently, restart it and check the temperature gauge.
If the temperature gauge needle has gone down, resume driving. If it has not gone
down, contact a dealer for repairs.
1
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only.
Have a dealer flush the system with proper antifreeze
as soon as possible.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve Tank
MAX
MIN
567
Han
d
lin
g the U
n
expected
Indicator, Coming On/Blinking
If the Engine Oil Low Warning Appears
■
Reasons for the warning to appear
Appears when the engine oil pressure is low.
■
What to do as soon as the warning
appears
1.
Immediately park the vehicle on level
ground in a safe place.
2.
If necessary, turn the hazard warning lights
on.
■
What to do after parking the vehicle
1.
Stop the engine and let it sit for
approximately three minutes.
2.
Open the hood and check the oil level.
u
Add oil as necessary.
2
P. 511
3.
Start the engine and check the
Engine Oil
Low
warning.
u
The warning disappears: Start driving
again.
u
The warning does not disappear within
10 seconds: Immediately stop the engine
and contact a dealer for repairs.
1
NOTICE
Running the engine with low oil pressure can cause
serious mechanical damage almost immediately.
568
uu
Indicator, Coming On/Blinking
u
If the Charging System Indicator Comes On
Han
d
lin
g the U
n
expected
If the Charging System Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the battery is not being charged.
■
What to do when the indicator comes on
Turn off the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
If the Malfunction Indicator Lamp Comes On or Blinks
■
Reasons for the indicator lamp to come on or blink
•
Comes on when there is a problem with the engine emissions control
system.
•
Blinks when engine misfiring is detected.
■
What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at a
dealer.
■
What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the engine stopped until it cools.
1
If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.
1
If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE
If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer at
31 mph (50 km/h) or less. Have your vehicle
inspected.
569
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On
■
Reasons for the indicator to come on
•
The brake fluid is low.
•
There is a malfunction in the brake system.
■
What to do when the indicator comes on while driving
Depress the brake pedal lightly to check pedal pressure.
•
If normal, check the brake fluid level the next time you stop.
•
If abnormal, take immediate action. If necessary, downshift the
transmission to slow the vehicle using engine braking.
If the Electric Power Steering (EPS) System Indicator Comes On
■
Reasons for the indicator to come on
•
Comes on when there is a problem with the EPS system.
•
If you depress the accelerator pedal repeatedly to increase the engine
speed while the engine is idling, the indicator comes on, and
sometimes the steering wheel becomes harder to operate.
■
What to do when the indicator comes on
Stop the vehicle in a safe place and restart the engine.
If the indicator comes on and stays on, immediately have your vehicle
inspected by a dealer.
1
If the Brake System Indicator (Red) Comes On
Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If there
is no resistance from the brake pedal, stop
immediately in a safe place. If necessary downshift
the gears.
If the brake system indicator and
ABS
indicator come
on simultaneously, the electronic brake distribution
system is not working. This can result in vehicle
instability under sudden braking.
Have your vehicle inspected by a dealer immediately.
U.S.
Canada
570
uu
Indicator, Coming On/Blinking
u
If the Low Tire Pressure/Tire Pressure Monitoring System (TPMS) Indicator Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Low Tire Pressure/Tire Pressure Monitoring
System (TPMS) Indicator Comes On or Blinks
■
Reasons for the indicator to come on or blink
A tire pressure is significantly low. If there is a problem with the TPMS
with Tire Fill Assist or the compact spare tire is installed, the indicator
blinks for about one minute, and then stays on.
■
What to do when the indicator comes on
Stop your vehicle in a safe place. Check the tire pressure and adjust the
pressure to the specified level. The specified tire pressure is on a label on
the driver side doorjamb.
■
What to do when the indicator blinks, then remains on
Have the tire inspected by a dealer as soon as possible. If the compact
spare tire causes the indicator to blink, change the tire to a full-size tire.
The indicator goes off after driving for a few miles (kilometers).
1
If the Low Tire Pressure/Tire Pressure Monitoring System (TPMS)
Indicator Comes On or Blinks
NOTICE
Driving on an extremely underinflated tire can cause
it to overheat. An overheated tire can fail. Always
inflate your tires to the prescribed level.
TPMS with Tire Fill Assist provides visual and audible
assistance during tire pressure adjustment. With the
power mode in ON, while you adjust tire pressure up
or down, the system alerts you as follows:
Below recommended pressure:
The beeper
sounds and exterior lights flash once every five
seconds.
At recommended pressure:
The beeper sounds
and exterior lights flash rapidly for ~ five seconds.
Above recommended pressure:
The beeper
sounds and lights flash twice every two seconds.
571
uu
Indicator, Coming On/Blinking
u
If the Transmission Indicator Blinks along with the Warning Message
Han
d
lin
g the U
n
expected
If the Transmission Indicator Blinks along with the Warning Message
■
Reasons for the indicator to blink
The transmission is malfunctioning.
■
What to do when the indicator blinks
•
Immediately have your vehicle inspected by
a dealer.
•
Change the gear position to
(
N
after
starting the engine.
u
Check if the
(
N
position in the
instrument panel and the indicator on
the
(
N
button light/blink.
u
The engine cannot be turned on unless
the parking brake is set.
2
1
If the Transmission Indicator Blinks along with the Warning Message
You may not be able to start the engine.
Make sure to set the parking brake when parking
your vehicle.
Call a professional towing service if you need to tow
your vehicle.
2
572
Han
d
lin
g the U
n
expected
Fuses
Fuse Locations
If any electrical devices are not working, set
the power mode to VEHICLE OFF (LOCK)
and check to see if any applicable fuse is
blown.
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
Located near the passenger's side damper
house. Push the tabs to open the box.
■
Engine Compartment Fuse Box Type A
Tab
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
−
(70 A)
REAR BLOWER
30 A
ABS/VSA MTR
40 A
ABS/VSA FSR
20 A
MAIN FAN
30 A
MAIN FUSE
150 A
2
SUB FAN
30 A
WIP MTR
30 A
WASHER
20 A
PREMIUM AMP
*
(20 A)
ENGINE MOUNT
30 A
FRONT BLOWER
40 A
A/C INVERTER
*
(30 A)
STANDARD AMP
*
(30 A)
REAR DEF
40 A
−
(30 A)
PREMIUM AMP
*
(20 A)
3
−
−
−
−
−
−
−
−
4
PARKING LIGHT
10 A
5
CRUISE CANCEL SW
7.5 A
6
STOP LIGHT
10 A
7
FI SUB VSS
10 A
8
L H/L LO
10 A
9
−
−
10
R H/L LO
10 A
11
IGPS
7.5 A
12
INJECTOR
20 A
13
H/L LO MAIN
20 A
14
VBUM
10 A
15
FRONT FOG
*
(10 A)
16
HAZARD
15 A
17
PASSENGER P/
SEAT(RECLINE)
*
(20 A)
18 PASSENGER P/SEAT(SLIDE)
*
(20 A)
19
−
−
20
MG CLUTCH
7.5 A
21
MAIN RLY
15 A
22
FI SUB
15 A
23
IG COIL
15 A
24
DBW
15 A
25
SMALL/STOP MAIN
20 A
26
BACK UP
10 A
27
HTD STRG WHEEL
*
(15 A)
28
HORN
10 A
29
RADIO/USB
15 A
Circuit Protected
Amps
* Not available on all models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст