Mitsubishi Colt Ralliart. Manual — part 327
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-52
CENTRAL DOOR LOCKING SYSTEM
INSPECTION PROCEDURE C-1: Central door locking system does not work.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENT ON TROUBLE SYMPTOM
If the central door locking system does not work at
all, the front door lock actuator (RH) or the
ETACS-ECU may be defective.
POSSIBLE CAUSES
• Malfunction of the front door lock actuator (RH)
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
ETACS-ECU
FUSIBLE
LINK
FRONT
DOOR LOCK
ACTUATOR
(RH)
FRONT
DOOR LOCK
ACTUATOR
(LH)
REAR
DOOR LOCK
ACTUATOR
(LH)
REAR
DOOR LOCK
ACTUATOR
(RH)
DOOR
UNLOCK
RELAY
DOOR
LOCK
RELAY
TAILGATE
LOCK
ACTUATOR
J/B SIDE
Central Door Lock Power Supply Circuit
6
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-53
DIAGNOSIS PROCEDURE
Step 1. Check the power supply circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning lamps
illuminate.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to Inspection Procedure A-2 "When
the ignition switch is at the LOCK (OFF)
position, the functions do not work normally.
Check the battery power supply circuit to
the ETACS-ECU
."
Step 2. Pulse check
Check the ETACS-ECU input signal related to the
central door locking system.
OK: The M.U.T.-III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to inspection procedure N-11 "The
driver's door lock actuator switch signal is
not received
Step 3. Connector check: B-134 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the defective connector.
Step 4. Check the wiring harness between B-134
ETACS-ECU connector terminal No.1 to fusible
link (6).
NOTE:
Prior to the wiring harness inspection, check junction
block connector B-108, and repair if necessary.
• Check the power supply line for open or short cir-
cuit.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the wiring harness.
Step 5. Retest the system.
Check that the central door locking system works
normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
).
NO :
Replace the ETACS-ECU.
System switch
Check condition
Driver's inside lock knob LOCK
→ UNLOCK
AC313872 AH
Connector: B-134
Harness side
Junction block (Rear view)
AC313872 AH
Connector: B-134
Harness side
Junction block (Rear view)
AC313870
Connector: B-108
BD
Junction block (Front view)
B-108(B)
Harness side
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-54
INSPECTION PROCEDURE C-2: A door can not be locked or unlocked by the central door locking
system.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
ETACS-ECU
FRONT
DOOR LOCK
ACTUATOR
(LH)
FRONT
DOOR LOCK
ACTUATOR
(RH)
REAR
DOOR LOCK
ACTUATOR
(LH)
REAR
DOOR LOCK
ACTUATOR
(RH)
TAILGATE LOCK
ACTUATOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
DOOR
UNLOCK
RELAY
DOOR
LOCK
RELAY
J/B SIDE
Central Door Lock Circuit
Main
Index
Group
TOC
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-55
COMMENT ON TROUBLE SYMPTOM
If a door can not be locked or unlocked by the central
door locking system, the door lock actuator may be
defective.
POSSIBLE CAUSES
• Malfunction of the door lock actuator
• Damaged harness wires and connectors
DIAGNOSTIC PROCEDURE
Step 1. Confirm which door lock actuator is
defective.
Q: Which door fails to lock correctly?
Driver's door :
Go to Step 2.
Front passenger's door :
Go to Step 5.
Rear right door :
Go to Step 8.
Rear left door :
Go to Step 11.
Tailgate :
Go to Step 14.
Step 2. Check the front door lock actuator (RH)
Check that the front door lock actuator (RH) works
normally. Refer to GROUP 42
− Door
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the front door lock actuator (RH).
Step 3. Connector check: B-132 ETACS-ECU
connector, D-08 front door lock actuator (RH)
connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the defective connector.
AC313872
Connector: B-132
AI
Harness side
Junction block (Rear view)
AC313880
Connector: D-08
AH
Harness side
D-08(B)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст