Mitsubishi Colt Ralliart. Manual — part 619
TROUBLESHOOTING
ACTIVE STABILITY CONTROL SYSTEM (ASC)
35C-21
STEP 6. Check for wheel bearing looseness
NOTE: Loose wheel bearing may increase the gap
between the wheel speed sensor and the wheel
speed detection magnet encoder. Check the wheel
bearing indicated by the code No. for looseness.
• Front: Refer to GROUP 26 − On-vehicle Service
• Rear: Refer to GROUP 27A − On-vehicle Service
Q: Is the check result normal?
YES :
Go to Step 7.
NO <when the relevant wheel is front> :
Replace
the wheel bearing. (Refer to GROUP 26
−
Front Axle Hub
NO <when the relevant wheel is rear> :
Replace
the rear hub assembly. (Refer to GROUP
27A
− Rear Axle Hub
.)
STEP 7. Wheel speed detection magnetic
encoder check
Check the wheel speed detection magnetic encoder
for adhesion of foreign materials or deformation.
NOTE: For the rear wheel speed detection magnetic
encoder, check from the mounting hole of the wheel
speed sensor by rotating the rear hub.
Q: Is the check result normal?
YES :
Go to Step 8.
NO <when the relevant wheel is front> :
When a
foreign material adheres to the encoder,
clean it. When the encoder is deformed,
replace the wheel bearing. (Refer to
GROUP 26
− Front Axle Hub
.)
NO <when the relevant wheel is rear> :
When a
foreign material adheres to the encoder,
clean it. When the encoder is deformed,
replace the rear hub assembly. (Refer to
GROUP 27A
− Rear Axle Hub
.)
Diagnosis code No.
Relevant
sensor
C1201
Front right
C1206
Front left
C1211
Rear right
C1216
Rear left
AC600965
<Front>
<Rear>
Encoder
AB
Encoder
Main
Index
Group
TOC
TROUBLESHOOTING
ACTIVE STABILITY CONTROL SYSTEM (ASC)
35C-22
STEP 8. Voltage measurement: A-05 ASC-ECU
connector
(1) Disconnect the connector, connect the ABS
check harness (Special tool: MB991984) to the
harness-side connector, and measure the voltage
at the special tool connector side.
NOTE: . Do not connect the special tool to
ASC-ECU.
(2) Ignition switch: ON
(3) Measure the voltage between the power supply
and signal terminals in the wheel speed sensor
circuit and body earth.
OK: 0 V
Q: Is the check result normal?
YES :
Go to Step 9.
NO (Not normal at the terminal No. 29 or 28) :
Go
to Step 10.
NO (Not normal at the terminal No. 34 or 13) :
Go
to Step 11.
NO (Not normal at the terminal No. 30 or 8) :
Go to
Step 12.
NO (Not normal at the terminal No. 11 or 10) :
Go
to Step 13.
AC601083
Connector: A-05
AB
A-05(Black)
Harness side
AC601085AB
MB991984
Check connector
ASC-ECU
ASC-ECU harness connector
Diagnosis code No.
Checking terminal
Power
supply
terminal
Signal
terminal
C1201
No. 29
No. 28
C1206
No. 34
No. 13
C1211
No. 30
No. 8
C1216
No. 11
No. 10
Main
Index
Group
TOC
TROUBLESHOOTING
ACTIVE STABILITY CONTROL SYSTEM (ASC)
35C-23
STEP 9. Measure the resistance at A-05 ASC-ECU
connector.
(1) Disconnect the connector, connect the ABS
check harness (Special tool: MB991984) to the
harness-side connector, and measure the voltage
at the special tool connector side.
NOTE: Do not connect the special tool to
ASC-ECU.
(2) Measure the resistance between the power
supply and signal terminals in the wheel speed
sensor circuit and body earth.
OK: No continuity
Q: Is the check result normal?
YES :
Go to Step 14.
NO (Not normal at the terminal No. 29 or 28) :
Go
to Step 10.
NO (Not normal at the terminal No. 34 or 13) :
Go
to Step 11.
NO (Not normal at the terminal No. 30 or 8) :
Go to
Step 12.
NO (Not normal at the terminal No. 11 or 10) :
Go
to Step 13.
STEP 10. Connector check: A-05 ASC-ECU
connector, A-29 wheel speed sensor <FR>
connector
Q: Is the check result normal?
YES :
Go to Step 16.
NO :
Repair the damaged connector.
AC601083
Connector: A-05
AB
A-05(Black)
Harness side
AC601085AC
MB991984
ASC-ECU
Check connector
ASC-ECU harness connector
Diagnosis code No.
Checking terminal
Power
supply
terminal
Signal
terminal
C1201
No. 29
No. 28
C1206
No. 34
No. 13
C1211
No. 30
No. 8
C1216
No. 11
No. 10
AC601083
Connector: A-05
AB
A-05(Black)
Harness side
AC601084
Connector: A-29
AB
Harness
side
A-29(black)
Main
Index
Group
TOC
TROUBLESHOOTING
ACTIVE STABILITY CONTROL SYSTEM (ASC)
35C-24
STEP 11. Connector check: A-05 ASC-ECU
connector, A-06 wheel speed sensor <FL>
connector
Q: Is the check result normal?
YES :
Go to Step 18.
NO :
Repair the damaged connector.
STEP 12. Connector check: A-05 ASC-ECU
connector, B-41 intermediate connector, C-06
wheel speed sensor <RR> connector
Q: Is the check result normal?
YES :
Go to Step 20.
NO :
Repair the damaged connector.
AC601083
Connectors: A-05, A-06
AC
A-05(Black)
A-05:
Harness side
A-06: Harness side
A-06 (Black)
AC601083
Connector: A-05
AB
A-05(Black)
Harness side
AC601092
Connector: B-41
AB
AC601093
Connector: C-06
AB
Harness side
C-06 (Black)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст