Mitsubishi Colt Ralliart. Manual — part 229
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-8
NOTE: *: This diagnosis code may be set if the
wheels spin or slip for a certain period (10 seconds
ore more). Verify the customer whether he/she
encountered such a driving condition. If yes, erase
the diagnosis code and complete the diagnosis proc-
ess. If no, there may be electrical noise in the wheel
speed sensor line. For each of the wheel speed sen-
sors, carry out troubleshooting (diagnosis code;
C1201, C1206, C1211 and C1216).
C1225*
Wheel speed sensor system
(sensor output failure)
Stores the diagnosis code if
the ABS control continues
for one minutes or more, or
the failed wheel is not
identified.
−
C1226
Control solenoid valve (FR) pressure holding system
Replace the hydraulic
unit (Integrated with
ABS-ECU) (Refer to
C1231
Control solenoid valve (FR) decompressing system
C1236
Control solenoid valve (FL) pressure holding system
C1241
Control solenoid valve (FL) pressure reducing system
C1246
Control solenoid valve (RR) pressure holding system
C1251
Control solenoid valve (RR) pressure reducing system
C1256
Control solenoid valve (RL) pressure holding system
C1261
Control solenoid valve (RL) decompressing system
C1266
Motor system (stuck)
C1273
Motor relay stuck off
C1274
Motor relay stuck on
C1276
Valve relay system
C1278
Valve relay system stuck off
C1279
Valve relay system stuck on
Replace the hydraulic
unit (Integrated with
ABS-ECU) (Refer to
C1607
Trouble in ABS-ECU
Replace the hydraulic
unit (Integrated with
ABS-ECU) (Refer to
C1860
ABS-ECU power supply system (abnormal voltage increase)
(16.8
± 1.0 V or more)
C1861
ABS-ECU power supply system (abnormal voltage drop) (9.6
± 0.3 V or more: ABS prohibit, 7.6 ± 0.3 V or less: ABS and
EBD prohibit)
U1073
Trouble in CAN bus system
Diagnosis code
No.
Inspection item
Diagnostic content
Reference page
Main
Index
Group
TOC
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-9
DIAGNOSIS TROUBLE CODE
PROCEDURES
Code No.C1200: Wheel speed sensor (FR) system (open circuit, short to earth or power supply)
OPERATION
The wheel speed sensor is a pulse generator. It con-
sists of encoder (a plate on which north and south
pole sides of the magnets are arranged alternately)
for detecting wheel speed which rotates at the same
speed as the road wheels. This sensor sends fre-
quency pulse signals in proportion to wheel speed.
The pulse signals, which the wheel speed sensor
creates, are sent to the ABS-ECU. The ABS-ECU
uses the frequency of the pulse signals to determine
the wheel speed.
DIAGNOSIS CODE SET CONDITIONS
The ABS-ECU monitors the voltage change in each
of the wheel speed sensor circuits. If the ECU
detects an open or short circuit in any of the circuits,
the ECU sets the diagnosis code.
PROBABLE CAUSES
• Damaged wiring harness or connector
• Malfunction of the wheel speed sensor
• Malfunction of the hydraulic unit (integrated with
ABS-ECU)
FRONT WHEEL SPEED SENSOR
(LH)
(RH)
(LH)
(RH)
ABS-ECU
REAR WHEEL SPEED SENSOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Wheel Speed Sensor Circuit
Main
Index
Group
TOC
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-10
DIAGNOSIS PROCEDURE
STEP 1. Remove the front right wheel speed
sensor and check it.
Refer to
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Replace the front right wheel speed sensor
(Refer to
STEP 2. Check the front right wheel speed
sensor connector A-29.
Check the connectors, for loose, corroded or dam-
aged terminals, or terminals pushed back in the con-
nector.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair or replace the damaged
component(s). Refer to GROUP 00, How to
Use Troubleshooting/Inspection Service
Points
− Connector Inspection Service
Points
.
STEP 3. Check the continuity (short to earth) at
ABS-ECU connector A-05.
(1) Disconnect the front right wheel speed sensor
connector A-29 and ABS-ECU connector A-05,
and connect special tool ABS Check Harness
(MB991951) to the wiring harness-side
connector.
AC313860AF
Connector : A-29
A-29(B)
Harness side
AC313863AB
Connector: A-05
Harness side
A-05(B)
AC314249AB
ABS-ECU
MB991951
Check connector
A-05 Harness connector
AC313860AF
Connector : A-29
A-29(B)
Harness side
Main
Index
Group
TOC
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-11
NOTE: Do not connect special tool ABS Check
Harness (MB991951) to the ABS-ECU.
(2) Continuity between ABS-ECU connector A-05
terminal 6 and body earth
OK: No continuity
(3) Continuity between ABS-ECU connector A-05
terminal 7 and body earth
OK: No continuity
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the wiring harness between
ABS-ECU connector A-05 and front right
wheel speed sensor connector A-29.
STEP 4. Resistance measurement at ABS-ECU
connector A-05.
(1) Disconnect the front right wheel speed sensor
connector A-29 and ABS-ECU connector A-05,
and connect special tool ABS Check Harness
(MB991951) to the wiring harness-side
connector.
NOTE: Do not connect special tool ABS Check
Harness (MB991951) to the ABS-ECU.
AC313972BC
Harness side
A-05
1
2
3
4
5
7
8
9
10
11
18
19
20
21
22
13
14
15
16
17
6
12
23
24
25
26
AC313972BD
Harness side
A-05
1
2
3
4
5
7
8
9
10
11
18
19
20
21
22
13
14
15
16
17
6
12
23
24
25
26
AC313863AB
Connector: A-05
Harness side
A-05(B)
AC314249AB
ABS-ECU
MB991951
Check connector
A-05 Harness connector
AC313860AF
Connector : A-29
A-29(B)
Harness side
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст