Mitsubishi Colt Ralliart. Manual — part 505
DOOR
BODY
42-42
REMOVAL SERVICE POINT
<<A>> POWER WINDOW REGULATOR
REMOVAL
1. Remove the door window glass installation bolts.
AC100009AC
MB990480
CAUTION
If tinting film is adhered to the door window
glass, attach special tool window glass holder
(MB990480) to the outside of the glass to prevent
the film from peeling off.
2. Lift the door window glass, and attach special tool
window glass holder (MB990480) to the glass as
shown to prevent the glass from falling.
3. Remove the window regulator.
INSTALLATION SERVICE POINTS
>>A<< LOWER SASH INSTALLATION
<REAR DOOR>
Engage the rear lower sash with the window sash
(door) securely.
INSPECTION
M1429001400583
POWER WINDOW SWITCH CONTINUITY
CHECK
Remove the power window switch (Refer to GROUP
52A, Door Trim
).
<MAIN SWITCH>
AC313194
1 2 3
4 5 6
7 8 9
12
10
13
11
14
Switch position Tester
connection
Specified
condition
FRONT
(LH)
UP
2
− 9*, 7 − 10
Continuity
(Less than 2
Ω)
OFF
2
− 7*, 2 − 9*
Continuity
(Less than 2
Ω)
DOW
N
2
− 7*, 9 − 10
Continuity
(Less than 2
Ω)
FRONT
(RH)
UP
2
− 14, 10 − 12
Continuity
(Less than 2
Ω)
OFF
2
− 12, 2 − 14
Continuity
(Less than 2
Ω)
DOW
N
2
− 12, 10 − 14
Continuity
(Less than 2
Ω)
REAR
(LH)
UP
1
− 10, 2 − 3*
Continuity
(Less than 2
Ω)
OFF
1*
− 2, 2 − 3*
Continuity
(Less than 2
Ω)
DOW
N
1*
− 2, 3 − 10
Continuity
(Less than 2
Ω)
REAR
(RH)
UP
2
− 6*, 4 − 10
Continuity
(Less than 2
Ω)
OFF
2
− 4*, 2 − 6*
Continuity
(Less than 2
Ω)
DOW
N
2
− 4*, 6 − 10
Continuity
(Less than 2
Ω)
NOTE: *: Set the window lock switch to UNLOCK
position.
Main
Index
Group
TOC
DOOR
BODY
42-43
<SUB SWITCH>
AC401445
8
3
1
4 5 6
2
7
Switch position Tester
connection
Specified
condition
UP
4
− 5, 6 − 7
Continuity
(Less than
2
Ω)
OFF
4
− 5, 7 − 8
Continuity
(Less than
2
Ω)
DOWN
4
− 6, 7 − 8
Continuity
(Less than
2
Ω)
POWER WINDOW MOTOR CONTINUITY
CHECK
<FRONT DOOR>
AC207678AB
Tester connection
Slider position
• Connect terminal No.
1 and the negative
battery terminal.
• Connect terminal No.
2 and the positive
battery terminal.
UP
• Connect terminal No.
2 and the negative
battery terminal.
• Connect terminal No.
1 and the positive
battery terminal.
DOWN
Main
Index
Group
TOC
DOOR
BODY
42-44
<REAR DOOR>
AC208131AB
Tester connection
Slider position
• Connect terminal No.
1 and the negative
battery terminal.
• Connect terminal No.
2 and the positive
battery terminal.
UP
• Connect terminal No.
2 and the negative
battery terminal.
• Connect terminal No.
1 and the positive
battery terminal.
DOWN
POWER WINDOW MOTOR CHECK
1. Connect a battery directly to the motor terminals
and check that the motor runs smoothly.
2. Check that the motor runs in the opposite
direction when the battery is connected with the
polarity reversed.
3. If defect is found, replace the window regulator as
an assembly.
Main
Index
Group
TOC
DOOR
BODY
42-45
DOOR HANDLE AND LATCH
REMOVAL AND INSTALLATION
M1423004600845
Pre-removal Operation
• Door Trim Assembly Removal (Refer to GROUP 52A,
Door Trim
Post-installation Operation
• Door Inside Handle Play Check (Refer to
).
• Door Outside Handle Play Check (Refer to
).
• Door Trim Assembly Installation (Refer to GROUP 52A,
Door Trim
AC208232AB
1
1
1
4
5
6
6
6
7
2
3
2
3
8
8
9
10
11
9
10
11
12
13
14
14
N
7
N
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
24 ± 4 N·m
24 ± 4 N·m
<Front door>
<Rear door>
Door handle and door latch
removal steps
>>
C
<<
1.
Door inside handle
•
Waterproof film (Refer to
).
>>
B
<<
2.
Rear lower sash
3.
Window glass runchannel rear
4.
Retainer
5.
Key cylinder <Drive’s side only>
6.
Door outside handle
•
Door window glass assembly
(Refer to
).
7.
Screw
8.
Door latch assembly
9.
Inside lock cable
10. Inside handle cable
11. Outside handle rod
12. Front door outside lock rod
13. Front door panel bracket
Door check removal steps
•
Waterproof film (Refer to
).
>>
A
14. Door check
Door handle and door latch
removal steps (Continued)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст