Mitsubishi 380. Manual — part 138
SPECIFICATIONS
INTERIOR
52A-60
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1521004100227
ITEM
SPECIFICATION
FRONT SEAT
Front seatback assembly bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Front seat cushion assembly bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Front seat bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Front seat nut
30
± 5 N⋅m (22 ± 4 ft-lb)
REAR SEAT
Seatback assembly bolt
22
± 4 N⋅m (16 ± 3 ft-lb)
FRONT SEAT BELT
Adjustable seat belt anchor bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Inner seat belt bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Outer seat belt bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
REAR SEAT BELT
Center seat belt outer and inner seat belt bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Inner seat belt bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Seat belt shoulder anchor bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
Seat belt lower anchor bolt
44
± 10 N⋅m (33 ± 7 ft-lb)
80-1
GROUP 80
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM. . . . . . . . . . . . . . . . . . . . . .
HOW TO READ CONFIGURATION
DIAGRAMS . . . . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT. . . . . . . . .
ENGINE AND TRANSMISSION . . . . .
DASH PANEL . . . . . . . . . . . . . . . . . . .
FLOOR, SEAT AND ROOF . . . . . . . .
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .
LUGGAGE COMPARTMENT . . . . . . .
OVERALL CONFIGURATION DIAGRAM
CONFIGURATION DIAGRAMS
80-2
OVERALL CONFIGURATION DIAGRAM
M1801000100558
NOTE:
.
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.
37DB222A
CONTROL WIRING
HARNESS
INJECTOR WIRING
HARNESS
<3.8L ENGINE>
INSTRUMENT PANEL
WIRING HARNESS
REAR DOME LIGHT
WIRING HARNESS
ROOF WIRING
HARNESS
FRONT WIRING
HARNESS
FLOOR WIRING
HARNESS
REAR DOOR
WIRING HARNESS
*
FRONT DOOR
WIRING HARNESS
*
HOW TO READ CONFIGURATION DIAGRAMS
CONFIGURATION DIAGRAMS
80-3
HOW TO READ CONFIGURATION DIAGRAMS
M1801000200555
The wiring harness diagrams clearly show the connector locations and harness configurations on actual vehi-
cles. Some variations are included in one configuration diagram. Accordingly, some diagrams may not be
applicable for individual vehicles.
37DB235A
Denotes connector No.
The same connector No. is used throughout the circuit diagrams to facilitate connector location searches.
The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number.
Numbers are usually assigned to parts in clockwise order on the diagram.
Example: A-30
Number specific to connector (serial number)
Connector location site symbol
A: ENGINE COMPARTMENT
D: FLOOR AND ROOF
B: ENGINE AND TRANSAXLE
E: DOOR
C: DASH PANEL
F: LUGGAGE COMPARTMENT
Denotes ground point.
Same ground number is used throughout circuit
diagrams to facilitate search of ground point.
Refer to GROUP 70 COMPONENT LOCATIONS
-GROUND MOUNTING LOCATIONS for details
of ground points.
Denotes the color of the tube
(If not specified, it is black).
R: Red
Y: Yellow
The number of connector pins and the connector color
(except milk white)* are shown for ease of retrieval.
Example: (6-B)
Connector color
(milk white if no color is indicated)
Number of connector pins
*: Typical connector colors
B: Black
BR: Brown
Y: Yellow
V: Violet
L: Blue
O: Orange
G: Green
GR: Grey
R: Red
NONE: Milk white
A-28 (2) FOG LAMP (RH)
A-34 (2) TURN SIGNAL (RH)
A-32 (6-B) HEADLAMP (RH)
A-29 (2-B) WINDSHIELD WASHER MOTOR
A-30 (3-B) DUAL PRESSURE SWITCH
Indicates the device to which the
connector is connected.
The mark shows the
standard mounting position
of wiring harness.
A-32
A-28
A-29
A-30
Y
Denotes a section covered by a
corrugated tube.
FRONT
WIRING
HARNESS
(RH)
Denotes harness name.
A-34
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст