Mitsubishi 380. Manual — part 557
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MFI)
13A-320
STEP 3. Measure the sensor supply voltage at throttle
position sensor harness side connector B-06.
(1) Disconnect the connector B-06 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground
• Voltage should be between 4.9 and 5.1 volts.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check harness connector B-20 at ECU for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 8.
03DB180A
CONNECTOR: B-06
B-06 (B)
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MFI)
13A-321
STEP 5. Check for open circuit and short circuit to ground
between throttle position sensor connector B-06 (terminal
No. 3) and ECU connector B-20 (terminal No. 10).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 8.
03DB180A
CONNECTOR: B-06
B-06 (B)
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MFI)
13A-322
STEP 6. Check for open circuit, short circuit to ground and
harness damage between throttle position sensor
connector B-06 (terminal No. 6) and ECU connector B-20
(terminal No. 42).
Q: Is the harness wire in good condition?
YES : Go to Step 7.
NO : Repair it. Then go to Step 8.
STEP 7. Replace the throttle body assembly.
(1) Replace the throttle body assembly.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0222 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
03DB180A
CONNECTOR: B-06
B-06 (B)
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
03DB180A
CONNECTOR: B-06
B-06 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MFI)
13A-323
STEP 8. Using diagnostic tool , read the diagnostic trouble
code (DTC).
CAUTION
To prevent damage to diagnostic tool , always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting diagnostic tool .
(1) Connect diagnostic tool to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P0222 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст