Mitsubishi 380. Manual — part 401
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-144
(P0758): Underdrive Solenoid Valve System
.
SOLENOID VALVE SYSTEM CIRCUIT
Refer to
.
.
CIRCUIT OPERATION
Refer to
.
.
DTC SET CONDITIONS
Check Conditions
• Solenoid status: either solid ON or OFF.
• Shift status: in-gear.
• Voltage of battery: 10 volts or more.
Judgement Criteria
• Solenoid voltage: 3 volts or less. (0.3 second)
• If (P0758) is set consecutively four times, the
transmission is locked into 3rd gear as a fail-safe
measure, and the "N" range light flashes once
per second.
.
OBD-II DRIVE CYCLE PATTERN
Start the engine, and keep the vehicle stopped in "P"
range for 5 seconds.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CODE TO BE
SET ARE:)
• Malfunction of the underdrive solenoid valve
• Damaged harness or connector
• Malfunction of the A/T-ECU
Circuit drawings
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• Refer to component locations GROUP-
DIAGNOSIS
Required Special Tool:
• MB991958: Diagnostic Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using diagnostic tool MB991958, check actuator
test item 02: Underdrive Solenoid Valve.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set diagnostic tool MB991958 to the actuator test mode.
• Item 02: Underdrive Solenoid Valve.
• An audible clicking or buzzing should be heard when
the underdrive solenoid valve is energized.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-145
STEP 2. Using diagnostic tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is (P1751) set? (P1751 may be set along with multiple
(P1751): A/T Control Relay
System.
NO : Go to Step 3.
STEP 3. Using diagnostic tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are (P0763) and (P0768) set? (Multiple DTCs may be
set).
YES : Go to Step 8.
NO : Go to Step 4.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-146
STEP 4. Measure the underdrive solenoid valve resistance
at A/T control solenoid valve assembly connector B-108.
(1) Disconnect connector B-108 and measure at the solenoid
valve side.
(2) Measure the resistance between solenoid valve assembly
connector B-108 terminals 3 and 9.
Resistance value: 2.7
−3.4 Ω [at 20°C (68°F)]
Q: Is the measured resistance 2.7
−3.4 Ω [at 20°C (68°F)]?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Measure the solenoid valve resistance at the
underdrive solenoid valve assembly inside the
transmission.
(1) Disconnect connector B-108-1 and measure at the solenoid
valve side.
(2) Measure the resistance between Underdrive solenoid valve
terminals 1 and 2.
Resistance value: 2.7
−3.4 Ω [at 20°C (68°F)]
Q: Is the measured resistance 2.7
−3.4 Ω [at 20°C (68°F)?
YES : Replace the harness wire between A/T control
solenoid valve assembly connector B-108 and the
solenoid valves.
NO : Replace the Underdrive solenoid valve. Refer to
GROUP 23B, Valve Body
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
AC210677
2
7
1
8
3
9
4
6
10
5
AB
B-108 HARNESS CONNECTOR:
A/T CONTROL SOLENOID VALVE
ASSEMBLY SIDE
VALVE BODY
ASSEMBLY
10DB109A
CONNECTORS: B-108-1
B-108-1
2
1
AC201141
B-108-1 HARNESS CONNECTOR:
UNDERDRIVE
SOLENOID VALVE SIDE
BA
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-147
STEP 6. Check A/T-ECU connector B-22 and A/T control
solenoid valve assembly connector B-108 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 7.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст