Mitsubishi 380. Manual — part 850
REAR SUSPENSION CROSSMEMBER
REAR SUSPENSION
34-26
>>C<< CROSSMEMBER STAY/CROSSMEMBER
NUT INSTALLATION
Ensure that the crossmember mounting bolts have been tight-
ened to specification, and then install the crossmember stay
with the crossmember nut.
INSPECTION
M1341006900089
• Check the crossmember for cracks or deformation.
• Check all bolts for condition and straightness.
AC306481AC
CROSSMEMBER
STAY
CROSSMEMBER
MOUNTING BOLT
CROSSMEMBER
NUT
SPECIFICATIONS
REAR SUSPENSION
34-27
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1341012700330
ITEM
SPECIFICATION
Lower arm assembly
Lower arm assembly to crossmember nut
78
± 7 N⋅m (57 ± 5 ft-lb)
Lower arm assembly to knuckle nut (self-locking nut)
113
± 12 N⋅m (83 ± 9 ft-lb)
Lower arm assembly to stabilizer bar link assembly nut
40
± 5 N⋅m (30 ± 3 ft-lb)
Rear suspension crossmember
Crossmember bracket mounting bolt and nut (self-locking
nut)
83
± 12 N⋅m (61 ± 9 ft-lb)
Crossmember stay (front) mounting bolt
45
± 5 N⋅m (34 ± 3 ft-lb)
Crossmember stay (rear) mounting bolt and nut
(self-locking nut)
83
± 12 N⋅m (61 ± 9 ft-lb)
Rear suspension crossmember to body bolt
108
± 17 N⋅m (79 ± 13 ft-lb)
Shock absorber assembly
Shock absorber assembly to body nut
45
± 5 N⋅m (34 ± 3 ft-lb)
Shock absorber assembly to knuckle bolt
100
± 10 N⋅m (74 ± 7 ft-lb)
Shock absorber self-locking nut (coil spring nut)
23
± 2 N⋅m (17 ± 1 ft-lb)
Stabilizer bar
Stabilizer bar link assembly nut
40
± 5 N⋅m (30 ± 3 ft-lb)
Stabilizer bracket bolt
45
± 5 N⋅m (34 ± 3 ft-lb)
Toe control arm assembly
Toe control arm assembly to crossmember nut
78
± 7 N⋅m (57 ± 5 ft-lb)
Toe control arm assembly to knuckle nut (self-locking nut)
66
± 6 N⋅m (49 ± 4 ft-lb)
Trailing arm assembly
Trailing arm assembly to knuckle nut (self-locking nut)
113
± 12 N⋅m (83 ± 9 ft-lb)
Trailing arm assembly to trailing arm bracket nut
(self-locking nut)
113
± 12 N⋅m (83 ± 9 ft-lb)
Trailing arm bracket to body bolt
105
± 10 N⋅m (77 ± 7 ft-lb)
Upper arm assembly
Upper arm assembly to crossmember bolt and nut
(self-locking nut)
113
± 12 N⋅m (83 ± 9 ft-lb)
Upper arm assembly to knuckle nut (self-locking nut)
113
± 12 N⋅m (83 ± 9 ft-lb)
SPECIFICATIONS
REAR SUSPENSION
34-28
GENERAL SPECIFICATIONS
M1341000200286
COIL SPRING
SERVICE SPECIFICATIONS
M1341000300421
LUBRICANT
M1341000400183
ITEM
3.8L ENGINE
Wire diameter mm (in)
12.0 (0.47)
Average diameter mm (in)
86.0
− 112.0 (3.39 − 4.40)
Free length mm (in)
322.0
ITEM
STANDARD VALUE
Camber
−0°50' ± 30' (Difference between
right and left within 30')
Toe-in mm (in)
3
± 3 (0.12 ± 0.12)
Toe control arm ball joint turning torque N
⋅m (in-lb)
1.0
− 2.6 (8.9 − 23)
Stabilizer bar link ball joint breakaway torque N
⋅m (in-lb)
3.4
− 9.0 (30 − 80)
ITEM
SPECIFIED LUBRICANT
QUANTITY
Toe control arm ball joint (lip and
inside of dust cover)
Multipurpose grease SAE J310, NLGI
No.2 or equivalent
7
± 0.5 g (0.247 ± 0.018 oz)
37-1
GROUP 37
POWER STEERING
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
POWER STEERING DIAGNOSIS . . .
INTRODUCTION TO POWER STEERING
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .
POWER STEERING DIAGNOSIS
TROUBLESHOOTING STRATEGY . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
STEERING WHEEL FREE PLAY CHECK .
STEERING ANGLE CHECK . . . . . . . . . . . .
TIE ROD END BALL JOINT BREAKAWAY
TORQUE CHECK . . . . . . . . . . . . . . . . . . . .
STATIONARY STEERING EFFORT CHECK
STEERING WHEEL RETURN TO CENTER
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRIVE BELT TENSION CHECK. . . . . . . . .
FLUID LEVEL CHECK . . . . . . . . . . . . . . . .
FLUID REPLACEMENT . . . . . . . . . . . . . . .
POWER STEERING SYSTEM AIR
BLEEDING . . . . . . . . . . . . . . . . . . . . . . . . .
OIL PUMP PRESSURE TEST . . . . . . . . . .
POWER STEERING PRESSURE SWITCH
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIE ROD END BALL JOINT DUST COVER
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING COLUMN SHAFT ASSEMBLY
SHOCK ABSORBING MECHANISM CHECK
STEERING WHEEL*. . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
STEERING SHAFT* . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
POWER STEERING GEAR BOX AND
LINKAGE* . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
Continued on next page
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING
•
Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
passenger (from rendering the SRS inoperative).
•
Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
•
MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection
with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст