Mitsubishi 380. Manual — part 313
TOWING AND HOISTING
GENERAL
00-30
CAUTION
• When service procedures require removing rear sus-
pension, fuel tank and spare tyre, place additional
weight on the rear end of vehicle, or anchor vehicle to
hoist to prevent tipping when the location of the center
of gravity changes.
• If the lifting support area contacts with the sill cover
(arrow area as shown in the illustration), the sill cover
will be damaged. Ensure that the lifting support does
not contact the sill cover.
00DB096A
Side view
Under view
SILL
COVER
AC307269
NOTCH
AB
NOTCH
GENERAL DATA AND SPECIFICATIONS
GENERAL
00-31
GENERAL DATA AND SPECIFICATIONS
M1001000900473
.
GENERAL SPECIFICATIONS
<3.8L ENGINE>
ITEM
380, 380LS, 380LX
380VRX, 380GT
Vehicle
dimension
mm
Front track
1 1,570mm
Overall width
2 1,840mm
Front overhang
3 984mm
989mm
Wheelbase
4 2,750mm
Rear overhang
5 1103mm
1116mm
Overall length
6 4837mm
4855mm
Ground clearance
(unladen
7 162mm
Overall height
(unladen)
8 1480mm
Rear track
9 1,570mm
ITEM
MANUAL TRANS.
AUTOMATIC TRANS.
380
380 VRX 380
380 VRX 380
LS/LX
380 GT
Vehicle
weight kg
Kerb mass (without
optional parts)
1,625
1,630
1,665
1,670
1,660
1,700
Kerb mass (with full
optional parts)
1,642
1,652
1,682
1,692
1,698
1,700
Maximum gross vehicle
mass
2,080
2,125
Maximum axle mass
rating-front
1,180
Maximum axle mass
rating-rear
1,010
Ride
height
(mm)
Front ride height
410
Measured from lowest point of
fender (wheel arch) to the centre
of the wheel.
Rear ride height
393
Seating
capacity
5
TIGHTENING TORQUE
GENERAL
00-32
TIGHTENING TORQUE
M1001001100555
Each torque value in the table is a standard value for
tightening under the following conditions.
1. Bolts, nuts and washers are all made of steel and
plated with zinc.
2. The threads and bearing surface of bolts and
nuts are all in dry condition.
The values in the table are not applicable:
1. If toothed washers are inserted.
2. If plastic parts are fastened.
3. If bolts are tightened to plastic or die-cast
inserted nuts.
4. If self-tapping screws or self-locking nuts are
used.
STANDARD BOLT AND NUT TIGHTENING TORQUE
Engine
Model No.
6G75
Total displacement
3,828cc
Automatic
Transaxle
Model No.
F5A5A-4-C2Z
Type
5-speed automatic
Manual
Trans.
Model No.
F 5M51
Type
5-speed manual
Fuel
system
Fuel supply system
Electronic controlled multipoint fuel injection (MPI)
ITEM
380, 380LS, 380LX
380VRX, 380GT
THREAD SIZE
STANDARD TIGHTENING TORQUE
NOMINAL BOLT
DIAMETER (mm)
PITCH
(mm)
HEAD MARK "4"
HEAD MARK "7"
HEAD MARK "8"
M5
0.8
2.5
± 0.5 N⋅m (23 ± 4
in-lb)
5.0
± 1.0 N⋅m (44 ± 9
in-lb)
6.0
± 1.0 N⋅m (53 ± 9
in-lb)
M6
1.0
5.0
± 1.0 N⋅m (44 ± 9
in-lb)
8.5
± 1.5 N⋅m (76 ± 13
in-lb)
10
± 2 N⋅m (89 ± 17
in-lb)
M8
1.25
11
± 2 N⋅m (98 ± 17
in-lb)
20
± 4 N⋅m (15 ± 3 ft-lb) 24 ± 4 N⋅m (18 ± 3 ft-lb)
M10
1.25
23
± 4 N⋅m (17 ± 3 ft-lb) 42 ± 8 N⋅m (31 ± 6 ft-lb) 53 ± 7 N⋅m (39 ± 5 ft-lb)
M12
1.25
42
± 8 N⋅m (31 ± 6 ft-lb) 80 ± 10 N⋅m (59 ± 7
ft-lb)
93
± 12 N⋅m (68 ± 9
ft-lb)
M14
1.5
70
± 10 N⋅m (52 ± 7
ft-lb)
130
± 20 N⋅m (96 ± 15
ft-lb)
150
± 20 N⋅m (111 ± 14
ft-lb)
M16
1.5
105
± 15 N⋅m (78 ± 11
ft-lb)
195
± 25 N⋅m (144 ± 18
ft-lb)
230
± 30 N⋅m (170 ± 22
ft-lb)
M18
1.5
150
± 20 N⋅m (111 ± 14
ft-lb)
290
± 40 N⋅m (214 ± 29
ft-lb)
335
± 45 N⋅m (247 ± 33
ft-lb)
TIGHTENING TORQUE
GENERAL
00-33
FLANGE BOLT AND NUT TIGHTENING TORQUE
M20
1.5
210
± 30 N⋅m (155 ± 22
ft-lb)
400
± 60 N⋅m (295 ± 44
ft-lb)
465
± 65 N⋅m (343 ± 48
ft-lb)
M22
1.5
290
± 40 N⋅m (214 ± 29
ft-lb)
540
± 80 N⋅m (398 ± 59
ft-lb)
630
± 90 N⋅m (465 ± 66
ft-lb)
M24
1.5
375
± 55 N⋅m (277 ± 40
ft-lb)
705
± 105 N⋅m (520 ±
77 ft-lb)
820
± 120 N⋅m (605 ±
88 ft-lb)
THREAD SIZE
STANDARD TIGHTENING TORQUE
NOMINAL BOLT
DIAMETER (mm)
PITCH
(mm)
HEAD MARK "4"
HEAD MARK "7"
HEAD MARK "8"
M6
1.0
5.0
± 1.0 N⋅m (44 ± 9
in-lb)
10
± 2 N⋅m (89 ± 17
in-lb)
12
± 2 N⋅m (107 ± 17
in-lb)
M8
1.25
13
± 2 N⋅m (111 ± 22
in-lb)
24
± 4 N⋅m (18 ± 3 ft-lb) 28 ± 5 N⋅m (20 ± 4 ft-lb)
M10
1.25
26
± 5 N⋅m (19 ± 4 ft-lb) 50 ± 5 N⋅m (37 ± 4 ft-lb) 58 ± 7 N⋅m (43 ± 5 ft-lb)
M10
1.5
25
± 4 N⋅m (18 ± 3 ft-lb) 46 ± 8 N⋅m (34 ± 6 ft-lb) 55 ± 5 N⋅m (41 ± 3 ft-lb)
M12
1.25
47
± 9 N⋅m (35 ± 6 ft-lb) 93 ± 12 N⋅m (68 ± 9
ft-lb)
105
± 15 N⋅m (78 ± 11
ft-lb)
M12
1.75
43
± 8 N⋅m (32 ± 6 ft-lb) 83 ± 12 N⋅m (61 ± 9
ft-lb)
98
± 12 N⋅m (72 ± 9
ft-lb)
THREAD SIZE
STANDARD TIGHTENING TORQUE
NOMINAL BOLT
DIAMETER (mm)
PITCH
(mm)
HEAD MARK "4"
HEAD MARK "7"
HEAD MARK "8"
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст