Mitsubishi 380. Manual — part 54
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-213
STEP 4. Check the ignition switch (IG2) circuit to the
sunroof motor assembly. Measure the voltage at sunroof
motor assembly connector D-04.
(1) Disconnect sunroof motor assembly connector D-04 and
measure the voltage available at the wiring harness side of
the connector.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 2 and ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Check the wiring harness between sunroof motor
assembly connector D-04 (terminal 2) and ignition switch
(IG2).
16DB359A
CONNECTOR: D-04
HARNESS SIDE
AC209365 FH
CONNECTOR D-04
(HARNESS SIDE)
16DB359A
CONNECTOR: D-04
HARNESS SIDE
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-214
NOTE: Also check junction block connectors C-215 and C-205
for loose, corroded, or damaged terminals, or terminals pushed
back in the connector. If junction block connector C-215 or
C-205 is damaged, repair or replace the damaged compo-
nent(s) as described in GROUP 00E, Harness Connector
Inspection
Q: Is the wiring harness between sunroof motor assembly
connector D-04 (terminal 2) and the ignition switch (IG2)
in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Check that
the sunroof works normally.
STEP 6. Check the ground circuit to the sunroof motor
assembly. Measure the resistance at sunroof motor
assembly connector D-04.
(1) Disconnect sunroof motor assembly connector D-04 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 8.
NO : Go to Step 7.
16DB360A
C-205
HARNESS SIDE
HARNESS SIDE
C-215
CONNECTORS: C-205,C-215
16DB359A
CONNECTOR: D-04
HARNESS SIDE
16DB361A
CONNECTOR D-04
(HARNESS SIDE)
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-215
STEP 7. Check the wiring harness between sunroof motor
assembly connector D-04 (terminal 5) and ground.
Q: Is the wiring harness between sunroof motor assembly
connector D-04 (terminal 5) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Check that
the sunroof works normally.
STEP 8. Check the sunroof switch connector D-03-1 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is sunroof switch connector D-03-1 in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check that the sunroof works normally.
16DB359A
CONNECTOR: D-04
HARNESS SIDE
AC307976
OVERHEAD CONSOLE
ASSEMBLY
CONNECTOR: D-03-1
HARNESS SIDE
AB
6
4
5
3 2 1
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-216
STEP 9. Check the sunroof switch.
(1) Remove the sunroof switch. Refer to GROUP 42, Sunroof
Assembly
(2) Check continuity when the sunroof switch is operated to
"OPEN", "TILT UP" or "CLOSE/TILT DOWN" positions.
Q: Does the check meet the specified conditions?
YES : Go to Step 10.
NO : Replace the sunroof switch. Check that the sunroof
works normally.
STEP 10. Check the ground circuit to the sunroof switch.
Measure the resistance at sunroof switch connector
D-03-1.
(1) Disconnect sunroof switch connector D-03-1 and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance between terminal 4 and ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 14.
NO : Go to Step 11.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OPEN
4
− 5
Less than 2 ohms
OFF
3
− 4, 3 − 5, 3 − 6,
4
− 5, 4 − 6, 5 − 6
Open circuit
TILT UP
3
− 4
Less than 2 ohms
CLOSE/TILT-DO
WN
4
− 6
Less than 2 ohms
AC306720
AC307038
AC209094
AB
OPEN
OVERHEAD CONSOLE
CLOSE/
TILT-DOWN
TILT-UP
SUNROOF SWITCH
AC307976
OVERHEAD CONSOLE
ASSEMBLY
CONNECTOR: D-03-1
HARNESS SIDE
AB
6
4
5
3 2 1
AC209364HH
CONNECTOR D-03-1
(HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст