Mitsubishi 380. Manual — part 905
HEADLAMP AND POSITION LAMP ASSEMBLY
CHASSIS ELECTRICAL
54A-154
REMOVAL SERVICE POINT
.
<<A>> HEADLAIGHT ASSEMBLY REMOVAL
Remove the front bumper mounting screw and clip.
16DB416A
FOG LAMP
CHASSIS ELECTRICAL
54A-155
FOG LAMP
FOG LAMP DIAGNOSIS
M1542000701366
The fog lamps are controlled by the Simplified Wiring
System (SWS). For troubleshooting, refer to GROUP
54B, SWS Diagnosis
ON-VEHICLE SERVICE
FOG LAMP AIMING
M1542001100472
PRE-AIMING INSTRUCTIONS
1. Inspect for badly rusted or faulty fog lamp assemblies.
2. These conditions must be corrected before a satisfactory
adjustment can be made.
3. Inspect tyre inflation, and adjust if necessary.
4. If the fuel tank is not full, place a weight in the trunk of the
vehicle to simulate weight of a full tank [0.8 kg per Litre].
5. There should be no other load in the vehicle other than
driver or substituted weight of approximately 70 kg (150
pounds) placed in driver's position.
6. Thoroughly clean the fog lamp lenses.
7. Measure centre of fog lamp lens, 41mm from anywhere of
the outer edge of the lens as shown in the illustration below.
8. Place the vehicle on a level floor, perpendicular to a flat
screen 10.0 meters away from the bulb centre-marks on the
foglamp lens that you have measured and marked.
9. Rock the vehicle sideways to allow the vehicle to assume its
normal position.
10.Bounce the front suspension through three (3) oscillations
by applying the body weight to the hood or bumper.
41mm
16DB579A
FOG LAMP
CENTRE
380 LS/LX
41mm
FOG LAMP
CENTRE
(380VRX, 380GT)
16DB575A
FOG LAMP
CHASSIS ELECTRICAL
54A-156
11.Measure the centre of the fog lamps as shown in the
illustration.
Four lines of adhesive tape (or equivalent markings) are
required on screen or wall:
(1) Position a vertical tape or mark so that it is aligned with
the vehicle centre line.
(2) Measure the distance from the centre of the fog lamp lens
to the floor. Transfer the measurement to the screen.
Horizontal tape or mark on the screen is for reference of
vertical adjustment.
(3) Measure the distance from the centre line of the vehicle
to the centre of each fog lamp. Transfer the measurement
to the screen. Vertical tape or mark on the screen is for
reference to the centre line of each fog lamp.
FOG LAMP ADJUSTMENT
1. Turn the adjusting screw to achieve the specified cut-off
location at the aiming screen.
NOTE: The horizontal direction is non-adjustable. If deviation of
the light beam axis exceeds the standard value, check that the
mounting location or some other points are not faulty.
16DB421A
SCREEN
(1)
(2)
(3)
(3)
FOG LAMP CENTRE
VEHICLE CENTRE
LINE
10.0m
16DB422A
HEIGHT OF FOG
LAMP CENTRE
V
(mm)
200mm
UPPER LIMIT
OF BEAM
HIGH INTENSITY
ZONE
380LS
16DB573A
ADJUSTING
SCREW
380VRX, 380GT
16DB574A
ADJUSTING
SCREW
FOG LAMP
CHASSIS ELECTRICAL
54A-157
BULB REPLACEMENT
M1542001300692
1. Remove the splash shield mounting 6 clips (A), then remove
the splash shield cover (B).
2. Depress the tab (C) on the harness connector and pull the
harness connector (D) to remove it.
3. Remove the entire socket and bulb assembly (E) by turning
it anticlockwise.
4. Remove the fog lamp bulb from the connector.
5. Replace the bulb, and then install the socket and bulb
assembly by turning it clockwise.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст