Mitsubishi 380. Manual — part 350
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-68
WARNING
If the air intake duct is removed from the throttle body take great care to keep fingers away
from the throttle plate. The drive motor has very high torque and is capable of random move-
ment at any time. Do not under any circumstances activate the throttle plate by hand.
When removing the throttle body from the intake manifold disconnect the wiring first. During
replacement connect the wiring last.
Do not activate the throttle body using a DC suppy to test the motor,as permanent damage to
the throttle body will result.
10 (B-20)
Throttle position
sensor power supply
Ignition switch: "ON"
4.9
− 5.1 V
57 (B-20)
Throttle position
sensor (sub)
(1) Accelerator pedal:
Released
(2) Accelerator pedal:
Depressed
(1) Throttle
valve fully
closed
1035
− 1250 mV
(2) Throttle
valve fully open
4000 mV or more
42 (B-20)
Throttle position
sensor (main)
(1) Accelerator pedal:
Released
(2) Accelerator pedal:
Depressed
(1) Throttle
valve fully
closed
1035
− 1250 mV
(2) Throttle
valve fully open
4000 mV or more
49 (B-20)
Throttle actuator
control motor (
−)
• Ignition switch: "ON"
• Accelerator pedal: fully closed to fully
opened
Decreases slightly
(approx. 2 V) from
battery voltage.
50 (B-20)
Throttle actuator
control motor (+)
• Ignition switch: "ON"
• Accelerator pedal: fully opened to fully
closed
Decreases slightly
(approx. 2 V) from
battery voltage.
TERMINAL
NO.
CHECK ITEM
CHECK CONDITION
NORMAL
CONDITION
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-69
SPECIAL TOOLS
M1172000600509
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main harness
A (Vehicles with CAN
communication
system)
D: MUT-III main harness
B (Vehicles without
CAN communication
system)
E: MUT-III main harness
C (for Daimler Chrysler
models only)
F: MUT-III measurement
adapter
G: MUT-III trigger
harness
MB991824-KIT
NOTE: G: MB991826
MUT-III trigger harness is
not necessary when
pushing V.C.I. ENTER
key.
Checking diagnostic
trouble codes
CAUTION
For vehicles with CAN
communication, use
MUT-III main harness A
to send simulated
vehicle speed. If you
connect MUT-III main
harness B or C instead,
the CAN
communication does
not function correctly.
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-70
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Inspection harness
B: LED harness
C: LED harness adapter
D: Probe
General service tools
Checking the continuity
and measuring the
voltage at the harness
connector
MB992044
Engine ECU check
harness
−
Measuring the terminal
voltage at the Engine
ECU
MB992045
Auto Trans. ECU check
harness
−
Measuring the terminal
voltage at the Auto Trans.
ECU
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991223
A
D
C
B
AD
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-71
ON-VEHICLE SERVICE
AUTO-CRUISE CONTROL SWITCH CHECK
M1172001200054
AUTO-CRUISE CONTROL MAIN SWITCH CHECK
1. Turn the ignition switch to the "ON" position.
2. Check that the "CRUISE" indicator lamp within the
combination meter illuminates when the "CRUISE" (MAIN)
switch is switched "ON".
AUTO-CRUISE CONTROL SETTING
1. Switch "ON" the "CRUISE" (MAIN) switch.
2. Drive at the desired speed, above approximately 40 km/h.
3. Push the auto-cruise control switch in the direction of the
arrow.
4. Check to be sure that when the switch is released the speed
is the desired constant speed.
NOTE: If the vehicle speed decreases to approximately 15
km/h below the set speed because of climbing a hill for
example, it is normal for the auto-cruise control to be can-
celled.
AC206195
16DB404A
AC305702
"CRUISE" INDICATOR
LIGHT
AUTO-CRUISE
CONTROL SWITCH
"CRUISE"
(MAIN)
SWITCH:
"ON"
ACX01172
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст