Mitsubishi 380. Manual — part 334
ENGINE CONTROL
ENGINE AND EMISSION CONTROL
17-4
SYMPTOM CHART
M1171002200292
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Throttle Valve Will Not Fully Open or Close
.
COMMENT
The throttle body or accelerator pedal position (APP)
sensor is suspected.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the throttle body.
• Malfunction of the accelerator pedal position
(APP) sensor.
• Malfunction of the Engine ECU.
Circuit drawings
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• Refer to component locations GROUP-
SYMPTOM
INSPECTION PROCEDURE
REFERENCE PAGE
Throttle Valve Will Not Fully Open or Close
1
Accelerator Pedal Operation Not Smooth (Over
Acceleration)
2
ENGINE CONTROL
ENGINE AND EMISSION CONTROL
17-5
DIAGNOSIS
Required Special Tools:
• MB991958: Diagnostic Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using Diagnostic Tool MB991958, read the
diagnostic trouble code (DTC).
CAUTION
To prevent damage to Diagnostic Tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting Diagnostic Tool
MB991958.
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
and the personal computer.
(4) Connect special tool MB991910 to special tool MB991824.
(5) Connect special tool MB991910 to the data link connector.
(6) Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator lamp will be illuminated in a green
color.
(7) Start the MUT-III system on the personal computer.
(8) Turn the ignition switch to the "ON" position.
(9) Check for MPI system diagnostic trouble code. (Refer to
GROUP 13A, MPI Diagnosis
− Diagnostic Function − How
to Read and Erase Diagnostic Trouble Code
(10)Turn the ignition switch to the "LOCK" (OFF) position, and
then remove Diagnostic Tool MB991958 in the reverse
order of installation.
Q: Is any DTC set?
YES : Repair MPI system.(Refer to GROUP 13A, MPI
Diagnosis
− Diagnostic Trouble Code Chart
Then go to Step 2.
NO : Go to Step 2.
STEP 2. Retest the system.
Q: Does the throttle valve fully open and close?
YES : The procedure is complete.
NO : Return to Step 1.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
ENGINE CONTROL
ENGINE AND EMISSION CONTROL
17-6
INSPECTION PROCEDURE 2: Accelerator Pedal Operation Not Smooth (Over Acceleration)
.
COMMENT
The accelerator pedal, its installation condition or the
accelerator pedal position (APP) sensor is sus-
pected.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the accelerator pedal.
• Incorrectly installed accelerator pedal.
• Malfunction of the accelerator pedal position
(APP) sensor.
Circuit drawings
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• Refer to component locations GROUP-
DIAGNOSIS
Required Special Tools:
• MB991958: Diagnostic Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Check if the accelerator pedal is installed
correctly.
Q: Is the accelerator pedal installed correctly?
YES : Go to Step 2.
NO : Replace and reinstall the accelerator pedal. (Refer to
). Go to Step 3.
ENGINE CONTROL
ENGINE AND EMISSION CONTROL
17-7
STEP 2. Using Diagnostic Tool MB991958, read the
diagnostic trouble code (DTC).
CAUTION
To prevent damage to Diagnostic Tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting Diagnostic Tool
MB991958.
(1) Ensure that the ignition switch is at the "LOCK" (OFF)
position.
(2) Start up the personal computer.
(3) Connect special tool MB991827 to special tool MB991824
and the personal computer.
(4) Connect special tool MB991910 to special tool MB991824.
(5) Connect special tool MB991910 to the data link connector.
(6) Turn the power switch of special tool MB991824 to the "ON"
position.
NOTE: When special tool MB991824 is energized, special
tool MB991824 indicator lamp will be illuminated in a green
color.
(7) Start the MUT-III system on the personal computer.
(8) Turn the ignition switch to the "ON" position.
(9) Check for MPI system diagnostic trouble code.(Refer to
GROUP 13A, MPI Diagnosis
− Diagnostic Function − How
to Read and Erase Diagnostic Trouble Code
) .
(10)Turn the ignition switch to the "LOCK" (OFF) position, and
then remove Diagnostic Tool MB991958 in the reverse
order of installation.
Q: Is any DTC set?
YES : Repair MPI system.(Refer to GROUP 13A, MPI
Diagnosis
− Diagnostic Trouble Code Chart
Then go to Step 3.
NO : Go to Step 3.
STEP 3. Retest the system.
Q: Does the accelerator pedal work normally?
YES : The procedure is complete.
NO : Return to Step 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст