Mitsubishi 380. Manual — part 764
ON-VEHICLE SERVICE
ENGINE LUBRICATION
12-4
4. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39
± 5 N⋅m (29 ± 3 ft-lb)
5. Refill the specified quantity of oil.
Select engine oil of ther proper SAE viscosity number
according to the atmospheric temperature SAE
0W-30, 5W-30 and 5W-40 engine oils can only be used
if they meet ACEA A3 and API SG (or higher) specififi-
cations.
Use engine oil conforming to the following classifica-
tion:
ACEA classification - "for service A1,A2 or A3"
API classification - "for service SG or higher"
Total quantity:(includes oil filter)
<3.8L Engine> 4.3 litres
6. Install the engine oil filler cap.
7. Check oil level.
ENGINE OIL FILTER REPLACEMENT
M1121001100424
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
− 90°C (176 −
194
°F).
WARNING
Use care as oil could be hot.
2. Remove the engine oil filler cap.
3. Remove the drain plug to drain oil.
4. Use an oil filter wrench to remove the engine oil filter.
5. Clean the filter bracket side mounting surface and ensure
the old O-ring has been removed.
AC305937
DRAIN PLUG
GASKET
OIL PAN SIDE
39 ± 5 N·m
29 ± 3 ft-lb
AB
<3.8L ENGINE>
AC000093
MB991610 OR
GENERAL
SERVICE
TOOL
AG
ON-VEHICLE SERVICE
ENGINE LUBRICATION
12-5
6. Apply a small amount of engine oil to the O-ring of the new
oil filter.
7. Screw on the oil filter by hand until it touches the surface of
the flange and then tighten it with an oil filter wrench.
8. Install the drain plug and refill engine oil (Refer to Engine Oil
9. Rev the engine a few times, and check to be sure that no
engine oil leaks at the oil filter.
ACX00396
O-RING
AB
NUMBER
ENGINE SPECIAL TOOL
TIGHTENING TORQUE
MD352627,
MD321589
3.8L
General service tool
Approximately one turn [14
± 2 N⋅m (124 ± 18 in-lb)]
ON-VEHICLE SERVICE
ENGINE LUBRICATION
12-6
ENGINE OIL PRESSURE CHECK
M1121002300614
Required Special Tool:
MD998054: Engine Oil Pressure Switch Wrench
1. Check engine oil quantity.
CAUTION
Since sealant is applied to the thread of the engine oil
pressure switch, take care not to damage the engine oil
pressure switch when removing it.
2. Use special tool MD998054 to remove the engine oil
pressure switch.
NOTE: Remove the terminal of oil pressure switch where
special tool MD998054 is not fitted.
3. Install the engine oil pressure gauge.
NOTE: Use a 1/8 pipe thread adapter.
4. Run the engine to warm it.
5. After the engine has been warmed up, check that engine oil
pressure is within the standard value.
Standard value:
At idle: 29 kPa (4.2 psi) or more
At 3,500 r/min: 294
− 686 kPa (43 − 100 psi)
6. Remove the engine oil pressure gauge.
7. Apply the specified sealant 3M
™ AAD Part number 8672 or
equivalent to the threads of the engine oil pressure switch.
AK203685
ENGINE OIL
PRESSURE
SWITCH
OIL FILTER
AC
<3.8L ENGINE>
AKX00294
MD998054
AB
AKX00295 AB
SPECIFICATIONS
ENGINE LUBRICATION
12-7
CAUTION
Do not start the engine within one hour after the engine
engine oil pressure switch has been installed.
8. Use special tool MD998054 to tighten the engine oil
pressure switch to the specified torque.
Tightening torque:
<3.8L ENGINE> 10
± 2 N⋅m (87 ± 17 in-lb)
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1121002200305
SERVICE SPECIFICATIONS
M1121000300221
SEALANT
M1121000500225
LUBRICANT
M1121000400701
AKX00294
MD998054
AB
ITEM
SPECIFICATION
Engine oil filter
MD136466, MD322508
17
± 3 N⋅m (13 ± 2 ft-lb)
Engine oil pan drain plug
39
± 5 N⋅m (29 ± 3 ft-lb)
Engine oil pressure switch
3.8L Engine
10
± 2 N⋅m (87 ± 17 in-lb)
ITEM
STANDARD VALUE
Engine oil pressure kPa (psi)
at idle
29 (4.2) or more
at 3,500 r/min
294
− 686 (43 − 100)
ITEM
SPECIFIED SEALANT
Engine oil pressure switch
3M
™ AAD Part No. 8672 or equivalent
ITEM
ENGINE OIL
QUANTITY (litres)
Oil filter
Engine oils conforming to ACEA A1, A2 or
A3 and API classification SG or higher.
0.3
Total quantity
3.8 L Engine
4.0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст