Mitsubishi 380. Manual — part 856
ON-VEHICLE SERVICE
POWER STEERING
37-22
5. Check the tilt pin fixing detent of the lower bracket for
deformation. If there is a deformation, replace the steering
column assembly.
CAUTION
• Be careful that nothing is pinched between the one-way
capsules and the body.
• Do not release the tilt lever until the steering column
has been installed to complete this inspection proce-
dure.
6. If no problem is found during the inspection, tighten the
steering column assembly mounting bolts to the specified
torque.
Tightening torque: 12
± 2 N⋅m (102 ± 22 in-lb)
AC308269 AB
TILT PIN
DETENT
STEERING WHEEL
POWER STEERING
37-23
STEERING WHEEL
REMOVAL AND INSTALLATION
M1372011400224
WARNING
•
Before removing the steering wheel and air bag module assembly, refer to GROUP 52B,
Service Precautions (
) and Air Bag Module and Clock Spring (
).
•
When removing and installing the steering wheel, do not let it bump against the air bag
module.
NOTE: For air bag module removal, refer to GROUP
52B, Air Bag Module and Clock Spring
.
Required Special Tool:
• MB990803: Steering Wheel Puller
Post-installation Operation
• Checking Steering Wheel Position with Wheels Straight
Ahead
AC306560
41 ± 8 N·m
30 ± 6 ft-lb
1
3
4
6
9.0 ± 2.0 N·m
80 ± 17 in-lb
AB
N
3.9 ± 0.9 N·m
35 ± 8 in-lb
2
5
2
2
REMOVAL STEPS
1.
STEERING WHEEL LOWER
COVER
<<A>>
2.
CONNECTORS (FOR HORN, AIR
BAG MODULE, AND STEERING
WHEEL REMOTE CONTROL
HARNESS)
3.
AIR BAG MODULE
4.
STEERING WHEEL DYNAMIC
DAMPER
5.
STEERING WHEEL REMOTE
CONTROL HARNESS
<<B>>
6.
STEERING WHEEL ASSEMBLY
INSTALLATION STEPS
•
CLOCK SPRING MATING MARK
ALIGNMENT (REFER TO GROUP
52B, AIR BAG MODULE AND
CLOCK SPRING
6.
STEERING WHEEL ASSEMBLY
5.
STEERING WHEEL REMOTE
CONTROL HARNESS
4.
STEERING WHEEL DYNAMIC
DAMPER
3.
AIR BAG MODULE
2.
CONNECTORS (FOR HORN, AIR
BAG MODULE, AND STEERING
WHEEL REMOTE CONTROL
HARNESS)
1.
STEERING WHEEL LOWER
COVER
INSTALLATION STEPS
STEERING WHEEL
POWER STEERING
37-24
REMOVAL SERVICE POINTS
.
<<A>> CONNECTOR (FOR AIR BAG MODULE)
REMOVAL
Slide the outer housing of the clock spring connector in the
arrow direction shown, and disconnect the connector.
.
<<B>>STEERING WHEEL ASSEMBLY REMOVAL
Use special tool MB990803 to remove the steering wheel.
AC306561AB
OUTER HOUSING OF THE
CLOCK SPRING CONNECTOR
AC000991AB
MB990803
STEERING SHAFT
POWER STEERING
37-25
STEERING SHAFT
REMOVAL AND INSTALLATION
M1372011500135
WARNING
Before removing the air bag module and steering wheel assembly, refer to GROUP 52B, Ser-
vice Precautions and Air Bag Module and Clock Spring (
Pre-removal Operation
• Air bag Module and Steering Wheel Assembly Removal
(Refer to
• Instrument Panel Lower Panel Removal (Refer to
GROUP 52A, Instrument Panel
• Floor Console Assembly Removal (Refer to GROUP 52A,
Floor Console Assembly
• Front Scuff Plate and Cowl Side Trim Removal (Refer to
GROUP 52A, Trims
).
• Trunk Lid Opener Cover Removal
• Accelerator Pedal Stopper Removal
• Front Floor Carpet Removal
Post-installation Operation
• Front Floor Carpet Installation
• Accelerator Pedal Stopper Installation
• Trunk Lid Opener Cover Installation
• Front Scuff Plate and Cowl Side Trim Installation (Refer to
GROUP 52A, Trims
).
• Floor Console Assembly Installation (Refer to GROUP
52A, Floor Console Assembly
).
• Instrument Panel Lower Panel Installation (Refer to
GROUP 52A, Instrument Panel
• Steering Wheel Assembly and Air bag Module Installation
(Refer to
AC306562 AB
12 ± 2 N·m
102 ± 22 in-lb
18 ± 2 N·m
13 ± 2 ft-lb
3
2
1
5
4
MOUNTING SCREW
REMOVAL STEPS
1.
STEERING COLUMN LOWER
COVER
2.
STEERING COLUMN UPPER
COVER
3.
CLOCK SPRING AND COLUMN
SWITCH ASSEMBLY (REFER TO
GROUP 52B, AIR BAG MODULE
AND CLOCK SPRING
4.
STEERING SHAFT PAD
<<A>> >>A<<
5.
STEERING COLUMN ASSEMBLY
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст