Mitsubishi 380. Manual — part 670
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54C-91
STEP 8. Check the CAN_H line (communication line only)
between joint connector (3) and the combination meter
connector for a short to the power supply. Measure the
voltage at joint connector (3) C-02.
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02 and combination meter
connector C-101, and measure the voltage at the wiring
harness side of joint connector (3) C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 4
and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between joint connector (3) and the
combination meter connector.
16DB476A
HARNESS SIDE
C-101
CONNECTORS: C-02, C-101
C-02
C-02
C-101
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365FQ
HARNESS SIDE: C-02
TEST
HARNESS
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54C-92
STEP 9. Check the CAN_H line (communication line
including the ETACS-ECU) between joint connector (3) and
the ETACS-ECU connector for a short to the power supply.
Measure the voltage at joint connector (3) C-02.
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02, and measure the
voltage at the wiring harness side of joint connector (3)
C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 5
and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 12.
NO : If the voltage measures more than 4.0 V, go to Step
10.
STEP 10. Check ETACS-ECU connector C-218 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is ETACS-ECU connector C-218 in good condition?
YES : Go to Step 11.
NO : Repair the damaged parts.
16DB408A
CONNECTOR: C-02
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365
HARNESS SIDE: C-02
TEST HARNESS
FR
16DB474A
C-218 (GR)
CONNECTOR: C-218
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54C-93
STEP 11. Check the CAN_H line (communication line only)
between joint connector (3) and ETACS-ECU connector for
a short to the power supply. Measure the voltage at joint
connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02 and ETACS-ECU
connector C-218, and measure the voltage at the wiring
harness side of joint connector (3) C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 5
and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between joint connector (3) and the
ETACS-ECU connector.
16DB408A
CONNECTOR: C-02
16DB474A
C-218 (GR)
CONNECTOR: C-218
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365
HARNESS SIDE: C-02
TEST HARNESS
FR
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54C-94
STEP 12. Check the CAN_H line (communication line
including the A/C-ECU) between joint connector (3) and
the A/C-ECU connector for a short to the power supply.
Measure the voltage at joint connector (3) C-02.
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
(1) Disconnect joint connector (3) C-02, and measure the
voltage at the wiring harness side of joint connector (3)
C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 6
and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 15.
NO : If the voltage measures more than 4.0 V, go to Step
13.
16DB408A
CONNECTOR: C-02
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365
HARNESS SIDE: C-02
FS
TEST HARNESS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст