Mitsubishi 380. Manual — part 58
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-229
STEP 2. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
• Ignition switch: ACC
• Windshield wiper switch: INT
(1) Operate the MUT-III according to the procedure below to
display "F.WIPER INT."
a. Select "Interactive Diagnosis."
b. Select "System select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "Function Diag."
f.
Select "WIPER."
g. Select "F.WIPER INT."
(2) Check that normal conditions are displayed for the items
described in the table below.
Q: Are normal conditions displayed for "INT WIPER SW"
and "FRONT ECU ACK"?
Normal conditions displayed for all the items : Go to
Step 3.
Normal condition is not displayed for the "INT WIPER
SW" : Replace the column switch. Verify that the windshield
wiper works normally.
Normal condition is not displayed for the "FRONT ECU
ACK" : Replace the front-ECU. Verify that the windshield
wiper works normally.
STEP 3. Check windshield wiper motor connector A-03 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is windshield wiper motor connector A-03 in good
condition?
YES : Go to Step 4.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield wiper works
normally.
ITEM NO.
ITEM NAME
NORMAL
CONDITION
ITEM 05
INT WIPER SW
ON
ITEM 70
FRONT ECU ACK
NORMAL ACK or
HI-BEAM ACK
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC302210
COLUMN SWITCH
CONNECTOR
COLUMN SWITCH
CONNECTOR AT
HARNESS SIDE
MB991812
AB
16DB425A
A-03 (B)
CONNECTOR: A-03
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-230
STEP 4. Check the windshield wiper motor.
(1) Disconnect windshield wiper motor connector A-03.
(2) Connect a battery to the windshield wiper motor as shown.
Then check that the windshield wiper motor operates
normally at high and low speeds.
Q: Does the windshield wiper motor operate normally?
YES : Go to Step 5.
NO : Replace the windshield wiper motor. Verify that the
windshield wiper works normally.
16DB425A
A-03 (B)
CONNECTOR: A-03
16DB426A
HIGH SPEED
LOW SPEED
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-231
STEP 5. Check the ground circuit to the windshield wiper
motor. Measure the resistance at the windshield wiper
motor connector A-03.
(1) Disconnect windshield wiper motor connector A-03 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 7.
NO : Go to Step 6.
STEP 6. Check the wiring harness between windshield
wiper motor connector A-03 (terminal 1) and ground.
Q: Is the wiring harness between windshield wiper motor
connector A-03 (terminal 1) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify the
windshield wiper works normally.
STEP 7. Check front-ECU connector A-12X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is front-ECU connector A-12X in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield wiper works
normally.
16DB425A
A-03 (B)
CONNECTOR: A-03
16DB427A
CONNECTOR A-03
(HARNESS SIDE)
16DB425A
A-03 (B)
CONNECTOR: A-03
AC305977
CONNCTOR: A-12X
AI
21
22
23
24
25
26
27
28
29
30
31
RELAY BOX SIDE
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-232
STEP 8. Check the ignition switch (ACC) circuit to the
front-ECU. Measure the voltage at front-ECU connector
A-12X.
(1) Disconnect front-ECU connector A-12X and measure the
resistance available at the relay box side of the connector.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 28 and ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Replace the front-ECU. Verify that the windshield
wiper works normally.
NO : Go to Step 9.
STEP 9. Check the wiring harness between front-ECU
connector A-12X (terminal 28) and the ignition switch
(ACC).
AC305977
CONNCTOR: A-12X
AI
21
22
23
24
25
26
27
28
29
30
31
RELAY BOX SIDE
AC209364CU
CONNECTOR A-12X
(RELAY BOX SIDE)
24
29
30
31
28 27
25
26
21
23 22
AC305977
CONNCTOR: A-12X
AI
21
22
23
24
25
26
27
28
29
30
31
RELAY BOX SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст