Mitsubishi 380. Manual — part 71
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-281
STEP 12. Check rear combination lamp (RH) connector
F-03 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is rear combination lamp (RH) connector F-03 in good
condition?
YES : Go to Step 14.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check that the taillamp (RH) illuminates
normally.
STEP 13. Check the stop/taillamp bulb (RH).
(1) Remove the stop/taillamp bulb (RH).
(2) Verify that the stop/taillamp bulb (RH) is not damaged or
burned out.
Q: Is the stop/taillamp bulb (RH) in good condition?
YES : Go to Step 14.
NO : Replace the stop/taillamp bulb (RH). Verify that the
taillamp (RH) illuminates normally.
STEP 14. Check the ground circuit to the rear combination
lamp (RH). Measure the resistance at rear combination
lamp (RH) connector F-03.
(1) Disconnect rear lamp (RH) connector F-03 and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 17.
NO : Go to Step 16.
AC305260
AH
CONNECTOR: F-03
HARNESS SIDE
AC305260
AH
CONNECTOR: F-03
HARNESS SIDE
AC209364
CONNECTOR F-03
(HARNESS SIDE)
HD
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-282
STEP 15. Check the wiring harness between rear
combination lamp (RH) connector F-03 (terminal 2) and
ground.
Q: Is the wiring harness between rear combination lamp
(RH) connector F-03 (terminal 2) and ground in good
condition?
YES : Replace the rear combination lamp socket (RH).
Verify that the taillamp (RH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillamp (RH) illuminates normally.
STEP 16. Check intermediate connector C-25 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is intermediate connector C-25 in good condition?
YES : Go to Step 17.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check that the taillamp (RH) illuminates
normally.
AC305260
AH
CONNECTOR: F-03
HARNESS SIDE
16DB435A
CONNECTOR: C-25
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-283
STEP 17. Check the wiring harness between rear
combination lamp (RH) connector F-03 (terminal 4) and
intermediate connector C-25 (terminal 8).
NOTE: Check intermediate connector C-25 for loose, corroded,
or damaged terminals, or terminals pushed back in the connec-
tor. If intermediate connector C-25 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between rear combination lamp
(RH) connector F-03 (terminal 4) and intermediate
connector C-25 (terminal 8) in good condition?
YES : Replace the rear combination lamp socket (RH).
Verify that the taillamp (RH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillamp (RH) illuminates normally.
16DB435A
CONNECTOR: C-25
AC305260
AH
CONNECTOR: F-03
HARNESS SIDE
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-284
STEP 18. Check front combination lamp (LH) connector
A-20 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is front combination lamp (LH) connector A-20 in good
condition?
YES : Go to Step 19.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Check that the front park lamp (LH)
illuminates normally.
STEP 19. Check the front park lamp bulb (LH).
(1) Remove the front park lamp bulb (LH).
(2) Verify that the front park lamp bulb (LH) is not damaged or
burned out.
Q: Is the front park lamp bulb (LH) in good condition?
YES : Go to Step 20.
NO : Replace the front park lamp bulb (LH). Verify that the
front park lamp (LH) illuminates normally.
STEP 20. Check the ground circuit to the front parking
lamp (LH). Measure the resistance at front combination
lamp (LH) connector A-20.
(1) Disconnect front combination lamp (LH) connector A-20
and measure the resistance available at the wiring harness
side of the connector.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 22.
NO : Go to Step 21.
16DB434A
A-20
CONNECTOR: A-20
16DB434A
A-20
CONNECTOR: A-20
16DB436A
CONNECTOR A-20
(HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст