Mitsubishi 380. Manual — part 823

SRS AIR BAG DIAGNOSIS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-216

SYMPTOM PROCEDURES

INSPECTION PROCEDURE 1: Communication between diagnostic tool and the SRS-ECU is not
possible.

.

TECHNICAL DESCRIPTION (COMMENT)

If the diagnostic tool (MUT-III Sub Assembly) can not
communicate with the SRS system, the CAN bus
lines may be defective. If the SRS system does not
work, the SRS-ECU or its power supply circuit may
be defective.

.

TROUBLESHOOTING HINTS (The most
likely causes for this case:)

• Damaged wiring harness or connector

• Malfunction of the SRS-ECU

• Refer to circuit diagrams GROUP-

90

• Refer to configuration diagrams GROUP-

80

.

DIAGNOSIS

Required Special Tools:

• MB991958: diagnostic tool (MUT-III Sub Assembly)

• MB991824: Vehicle Communication Interface (V.C.I.)

• MB991827: MUT-III USB Cable

• MB991910: MUT-III Main Harness A (Vehicles with CAN

communication system)

STEP 1. Using diagnostic tool MB991958, diagnose the
CAN bus line.

CAUTION

To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
Use diagnostic tool MB991958 to diagnose the CAN bus lines.
(1) Connect diagnostic tool MB991958 to the data link

connector.

(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.

Q: Is the check result satisfactory?

YES : Check and repair the power supply circuit system

(Refer to

P.52B-217

).

NO : Repair the CAN bus lines (Refer to GROUP 54C,

Diagnosis-Can Bus Diagnostic Chart ).

00DB076A

MB991910

DATA LINK

CONNECTOR

MB991824

MB991827

SRS AIR BAG DIAGNOSIS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-217

INSPECTION PROCEDURE 2: Power Supply Circuit System

.

CIRCUIT OPERATION

• The SRS-ECU is energized by the ignition switch

(IG1) through multi-purpose fuse 18 and the
SRS-ECU terminal 23 and multi-purpose fuse 19
and the SRS-ECU terminal 24.

• If the power supply to the SRS-ECU has failed,

diagnostic tool (MUT-III Sub Assembly) will not
be able to communicate with it.

.

TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)

• Damaged wiring harness or connector

• Defective battery

• Charging system failed

• Malfunction of the SRS-ECU

.

DIAGNOSIS

Required Special Tools:

• MB991958: diagnostic tool (MUT-III Sub Assembly)

• MB991824: Vehicle Communication Interface (V.C.I.)

• MB991827: MUT-III USB Cable

• MB991910: MUT-III Main Harness A (Vehicles with CAN

communication system)

.

24DB062A

CONNECTOR: C-121

C-121 (Y)

SRS-ECU

42

31

38

27

21

41

28

39

22

30

25

47

36

33

44

34

45

37

48

26

29

23

40

32

43

35

46

24

B

A

C-121

INSTRUMENT

HARNESS

CONNECTOR

(REAR VIEW)

SRS AIR BAG DIAGNOSIS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-218

STEP 1. Measure the resistance at SRS-ECU connector
C-121.
(1) Disconnect the connector C-121.

CAUTION

Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(2) Check for continuity between C-121 harness side connector

terminals 46 and body ground.
It should be 2 ohms or less.

Q: Is the measured resistance 2 ohms or less?

YES : Then go to Step 2.
NO : Repair the wiring harness between SRS-ECU

connector C-121 terminals 46 and the body ground.
Then go to Step 5.

STEP 2. Check the harness wires for short circuit to
ground between SRS-ECU connector C-121 (terminal
No.23 and 24) and ignition switch connector C-308
(terminal No.2).

24DB062A

CONNECTOR: C-121

C-121 (Y)

SRS-ECU

42

31

38

27

21

41

28

39

22

30

25

47

36

33

44

34

45

37

48

26

29

23

40

32

43

35

46

24

B

A

C-121

INSTRUMENT

HARNESS

CONNECTOR

(REAR VIEW)

24DB059A

42

31

38

27

21

41

28

39

22

30

25

47

36

33

44

34

45

37

48

26

29

23

40

32

43

35

46

24

B

A

C-121 HARNESS SIDE
CONNECTOR (REAR VIEW)

35DB042A

CONNECTOR: C-308

C-308

2

5

4

1

6

3

24DB062A

CONNECTOR: C-121

C-121 (Y)

SRS-ECU

42

31

38

27

21

41

28

39

22

30

25

47

36

33

44

34

45

37

48

26

29

23

40

32

43

35

46

24

B

A

C-121

INSTRUMENT

HARNESS

CONNECTOR

(REAR VIEW)

SRS AIR BAG DIAGNOSIS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-219

NOTE: After inspecting intermediate connectors , C-211 and
C-215 inspect the wiring harness. If intermediate connectors ,
C-211 and C-215 are damaged, repair or replace wiring har-
ness. Refer to GROUP 00E, Harness Connector Inspection .
Then go to Step 5.

Q: Are the harness wires between SRS-ECU connector

C-121 (terminal No.23 and 24) and ignition switch
connector C-308 (terminal No.2) in good condition?
YES : Go to Step 3.
NO : Replace the harness wires between SRS-ECU

connector C-121 and ignition switch connector C-308.
Then go to Step 5.

STEP 3. Check the battery.
Check the battery (Refer to GROUP 54A, Battery test ).

Q: Is the battery in good condition?

YES : Go to Step 4.
NO : Charge or replace the battery. Then go to Step 5.

STEP 4. Check the charging system.
Check the charging system (Refer to GROUP 16, Charging
system diagnosis ).

Q: Is the charging system in good condition?

YES : Go to Step 5.
NO : Repair or replace the charging system

component(s).Then go to Step 5.

STEP 5. Retest the system.

Q: Can the SRS-ECU communicate with the diagnostic tool

(MUT-III Sub Assembly)?
YES : It can be assumed that this malfunction is intermittent.

Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points

− How to

Cope with Intermittent Malfunctions .

NO : Replace the SRS-ECU (Refer to

P.52B-234

). Then go

to Step 6.

STEP 6. Retest the system.

Q: Can the SRS-ECU communicate with the diagnostic tool

(MUT-III Sub Assembly)?
YES : The procedure is complete.
NO : Go to Step 1.

52DB021A

CONNECTORS: C-211, C-215

HARNESS SIDE

C-211

HARNESS SIDE

C-215