Mitsubishi 380. Manual — part 753
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11A-14
ENGINE ASSEMBLY
REMOVAL AND INSTALLATION
M1112001000894
CAUTION
*: indicates parts which should be temporarily tightened, and then fully tightened with the engine
weight applied on the vehicle body.
Pre-removal Operation
• Under Cover Removal (Refer to GROUP 51, Under Cover
• Fuel Line Pressure Reduction [Refer to GROUP 13B,
On-vehicle Service
− Fuel Pump Relay Disconnection
(How to Reduce Pressurized Fuel Lines)
• Engine Coolant Draining (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
• Engine Oil Draining (Refer to GROUP 12, On-vehicle Ser-
vice
− Engine Oil Replacement
.)
• Hood Removal (Refer to GROUP 42, Hood
• Engine Control Unit (ECU) Removal (Refer to GROUP
13B, Engine Control Unit (ECU)
• Air Cleaner Removal (Refer to GROUP 15, Air Cleaner
.)
• Front Exhaust Pipe Removal (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Strut Tower Bar Removal (Refer to GROUP 42, Strut
Tower Bar
.)
• Battery and Battery Tray Removal
• Radiator Grille Removal (Refer to GROUP 51, Radiator
Grille
.)
Post-installation Operation
• Right Bank Exhaust Manifold Installation (Refer to
GROUP 15, Exhaust Manifold
• Radiator Grille Installation (Refer to GROUP 51, Radiator
Grille
.)
• Battery and Battery Tray Installation
• Strut Tower Bar Installation (Refer to GROUP 42, Strut
Tower Bar
.)
• Air Cleaner Installation (Refer to GROUP 15, Air Cleaner
.)
• Front Exhaust Pipe Installation (Refer to GROUP 15,
Exhaust Pipe and Main Muffler
• Engine Control Unit (ECU) Installation (Refer to GROUP
13B, Engine Control Unit (ECU)
• Hood Installation (Refer to GROUP 42, Hood
.)
• Drive Belt Tension Check (Refer to
• Engine Oil Refilling (Refer to GROUP 12, On-vehicle Ser-
vice
− Engine Oil Replacement
.)
• Engine Coolant Refilling (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
• Fuel Leak Check
• Under Cover Installation (Refer to GROUP 51, Under
.)
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11A-15
01DB040AB
3.0 ± 0.5 N·m
27 ± 4 in-lb
9.0 ± 2.0 N·m
80 ± 17 in-lb
9.0 ± 2.0 N·m
80 ± 17 in-lb
1
2
4
5
6
(ENGINE OIL)
REMOVAL STEPS
1.
ENGINE COVER
2.
CONTROL WIRING HARNESS
CONNECTION
4.
PURGE HOSE CONNECTION
<<A>>
>>C<<
5.
FUEL HIGH-PRESSURE HOSE
CONNECTION
6.
HEATER HOSE CONNECTION
•
DRIVE SHAFT (REFER TO
GROUP 26, DRIVE SHAFT
ASSEMBLY
<<B>>
•
EXHAUST MANIFOLD (RH)
(REFER TO GROUP 15,
EXHAUST MANIFOLD
.)
REMOVAL STEPS (Continued)
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11A-16
Required Special Tools:
• MB991454: Engine Hanger Balancer
• MB991895: Engine Hanger
• MB991928: Engine Hanger
AC306783
12 ± 2 N·m
102 ± 22 in-lb
12 ± 2 N·m
102 ± 22 in-lb
42 ± 7 N·m
31 ± 5 ft-lb
46 ± 8 N·m
34 ± 6 ft-lb
108 ± 10 N·m*
80 ± 9 ft-lb*
36 ± 6 N·m
27 ± 4 ft-lb
9.0 ± 2.0 N·m
80 ± 17 in-lb
15
18
11
16
13
8
12
7
14
17
9
10
20
N
AB
19
108 ± 10 N·m*
80 ± 9 ft-lb*
7.
GENERATOR DRIVE BELT
8.
POWER STEERING OIL PUMP
DRIVE BELT
9.
A/C COMPRESSOR ASSEMBLY
CONNECTOR
<<C>>
10. A/C COMPRESSOR ASSEMBLY
11. POWER STEERING PRESSURE
SWITCH CONNECTOR
<<D>>
12. POWER STEERING OIL PUMP
13. POWER STEERING PRESSURE
HOSE CLAMP BRACKET
<<E>>
•
RADIATOR (REFER TO GROUP
14, RADIATOR
•
TRANSAXLE ASSEMBLY (REFER
TO GROUP 23A, TRANSAXLE
ASSEMBLY <F4A5A>
.)
14. ENGINE MOUNTING STAY
15. GROUNDING CABLE
CONNECTION
16. POWER STEERING OIL
RESERVOIR
17. SELF-LOCKING NUTS
>>B<<
18. ENGINE FRONT MOUNTING
BRACKET
19. MOUNTING BOLT
<<H>>
>>A<<
20. ENGINE ASSEMBLY
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11A-17
REMOVAL SERVICE POINTS
.
<<A>> FUEL HIGH-PRESSURE HOSE REMOVAL
1. Remove the fuel high-pressure hose stopper.
2. Remove the fuel high-pressure hose in the direction shown
in the figure while the retainer is pulled up.
NOTE: If the retainer is released, install it after removing the
fuel high-pressure hose.
.
<<B>> EXHAUST MANIFOLD (RH) REMOVAL
Remove the center exhaust pipe, and pull out the exhaust man-
ifold (RH) between the crossmember and cylinder block.
.
<<C>> A/C COMPRESSOR ASSEMBLY REMOVAL
Remove the compressor from the compressor bracket with the
hose still attached.
NOTE: Place the removed A/C compressor where it will not be
a hindrance when removing and installing the engine assembly,
and secure it with a cord or wire.
.
<<D>> POWER STEERING OIL PUMP REMOVAL
Remove the power steering oil pump from the engine with the
hose attached.
NOTE: Place the removed power steering oil pump in a place
where it will not be a hindrance when removing and installing
the engine assembly, and secure it with a cord or wire.
.
AC304581
AB
STOPPER
AC304582
AB
RETAINER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст