Mitsubishi 380. Manual — part 255
GENERAL DESCRIPTION
POWER PLANT MOUNT
32-2
GENERAL DESCRIPTION
M1321000100373
• The engine front mounting bracket is a
dome-shaped fluid-filled mount for improved
responsiveness during acceleration and more
stable vehicle performance against road distur-
bances.
• The liquid-filled transaxle mounting body side
bracket improves riding comfort by its refined
insulator.
• A roll stopper bracket in the upper area limits
engine rolling. Furthermore, large diameter insu-
lator reduces idle vibration.
CONSTRUCTION DIAGRAM
ENGINE FRONT
MOUNTING
BRACKET
TRANSAXLE MOUNTING
BODY SIDE BRACKET
ENGINE FRONT
ROLL STOPPER
BRACKET
CENTERMEMBER
ENGINE REAR
ROLL STOPPER
BRACKET
FRONT AXLE NO.1
CROSSMEMBER
21DB021A
SPECIAL TOOL
POWER PLANT MOUNT
32-3
SPECIAL TOOL
M1321000600390
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991897
Ball joint remover
MB991113-01,
MB990635-01 or
General service tool
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also
used to disconnect the knuckle
and tie rod end ball joint.
AC106827
ENGINE MOUNTING
POWER PLANT MOUNT
32-4
ENGINE MOUNTING
REMOVAL AND INSTALLATION
M1321001100462
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
Raise the engine and transaxle assembly until its weight is
not applied to the insulator, and support it securely.
21DB014A
2
3
108 ± 10 N·m*
80 ± 9 ft-lb*
N
36 ± 6 N·m
27 ± 4 ft-lb
108 ± 10 N·m*
80 ± 9 ft-lb*
4
5
6
7
5 ± 1 N·m
3 ± 0.5 ft-lb
108 ± 10 N·m*
80 ± 9 ft-lb*
REMOVAL STEPS
2.
ENGINE MOUNTING STAY
3.
MOUNTING BOLT
4.
SELF LOCKING NUTS
5.
ENGINE MOUNT BRACKET
6.
ENGINE MOUNT STOPPER
7.
DYNAMIC DAMPER
REMOVAL STEPS (Continued)
TRANSAXLE MOUNTING
POWER PLANT MOUNT
32-5
TRANSAXLE MOUNTING
REMOVAL AND INSTALLATION
M1321001400452
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
• Engine Control Unit (ECU) , Refer to GROUP 13B,
Engine Control Unit (ECU)
).
• Air Cleaner Removal (Refer to GROUP 15, Air Cleaner
).
• Battery and Battery Tray Removal
• Centremember Removal (Refer to
).
• Engine Rear Roll Stopper Bracket Removal (Refer to
).
• Raise the engine and transaxle assembly until its weight
is not applied to the insulator, and support it securely.
Post-installation Operation
• Engine Rear Roll Stopper Bracket Installation (Refer to
).
• Centremember Installation (Refer to
).
• Battery and Battery Tray Installation
• Air Cleaner Installation (Refer to GROUP 15, Air Cleaner
).
• Engine Control Unit (ECU) Installation, Refer to GROUP
13B, Engine Control Unit (ECU)
21DB022A
1
2
3
83 ± 12 N·m*
61 ± 9 ft-lb*
83 ± 12N·m*
61 ± 5 ft-lb*
N
3
REMOVAL STEPS
1.
SELF-LOCKING NUTS
2.
TRANSAXLE MOUNTING BODY
SIDE BRACKET
>>A<<
3.
TRANSAXLE MOUNTING
STOPPER
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст