Mitsubishi 380. Manual — part 210
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-136
ACTUATOR TEST REFERENCE
M1554005200133
MUT-III DIAGNOSTIC
TOOL DISPLAY
ITEM NO.
INSPECTION ITEM
DRIVE CONTENT
Blower fan: OFF
83
Blower motor
OFF
Blower fan: Middle
84
Middle speed
Blower fan: High
85
High speed
Air mix damper motor:
0%
42
Air mixing damper control motor
Opening degree: approx.
0% (Max cool)
Air mix damper motor:
100%
43
Opening degree: approx.
100% (Max hot)
Air outlet c/o damper:
FACE
70
Mode selection damper control
motor
FACE
Air outlet c/o damper: Bi_
Level
67
FOOT/FACE
Air outlet c/o damper:
FOOT
71
FOOT
Air outlet c/o damper:
DEF/FOOT
69
DEF/FOOT
Air outlet c/o damper:
DEF
68
DEF
Idle up request: high load 74
Idle speed
HIGH idle up
Idle up request: low load 75
LOW idle up
Idle up request: OFF
76
OFF
Rear defogger switch:
OFF
40
Rear window defogger switch
Rear window defogger: OFF
Rear defogger switch:
ON
41
Rear window defogger: ON
Idle up request: OFF
50
Idle up operation
Idle up: OFF
Idle up request: low load 51
Idle up: low load
Idle up request: high load 52
Idle up: high load
Condenser: 0%
77
Condenser fan
OFF
Condenser: 50%
79
Middle speed
Rheostat: 0%
80
Rheostat- Illumination control
OFF
Rheostat: 100%
81
Full duty
Rheostat: 50%
82
Half duty
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-137
CHECK AT A/C-ECU TERMINAL
M1552010300572
8
2
1
5
3 4
6 7
9 10
20
19
18
17
16
15
14
13
12
11
32
24
29
21
31
30
2223
27
35
33
25
34
26
36
28
AC210339
C-15
C-16
AB
TERMINAL
NO.
CHECK ITEM
CHECKING REQUIREMENTS
NORMAL CONDITION
1
Air mixing damper control motor When the air mix damper is
moved to the MAX. COOL
position.
10 V
When the air mix damper is
moved to the MAX. HOT
position.
0.5 V
2
Air mixing damper control motor When the air mix damper is
moved to the MAX. COOL
position.
0.5 V
When the air mix damper is
moved to the MAX. HOT
position.
10 V
3
Back-up power supply
Always
Battery positive voltage
4
Mode selection damper control
motor (DEF)
When the damper is moved to
the FACE position.
0.5 V
When the damper is moved to
the DEF position.
10 V
5
Outside/inside air selection
damper control motor (outside)
When the damper is moved to
the inside air recirculation
position.
0.5 V
When the damper is moved to
the outside air induction
position.
0 V (when the motor is
stopped)
6
Outside/inside air selection
damper control motor (inside)
When the damper is moved to
the inside air recirculation
position.
0 V (when the motor is
stopped)
When the damper is moved to
the outside air induction
position.
0.5 V
8
Rear defogger relay
Ignition switch: ON
Battery positive voltage
9
Front blower relay
Ignition switch: ON
Battery positive voltage
10
A/C compressor relay
A/C compressor relay: ON
Battery positive voltage
11
Mode selection damper control
motor (FACE)
When the damper is moved to
the FACE position.
10 V
When the damper is moved to
the DEF position.
0.5 V
12
A/C pressure sensor
Ignition switch: ON
5 V
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-138
16
Potentiometer power supply
Ignition switch: ON
5 V
17
Power transistor (BASE)
When the blower speed
selection dial shows Maximum
air volume.
1 V
18
Power transistor
(COLLECTOR)
When the blower speed
selection dial shows Maximum
air volume.
12.1 V
19
Photo sensor
Ignition switch: ON
5 V
20
Sensors and potentiometers
ground
Always
0 V
21
Mode selection damper control
motor potentiometer input
When the damper is moved to
the FACE position.
4 V
22
Interior temperature sensor
Ignition switch: ON
5 V
23
Ambient temperature sensor
input
When sensor temperature is
25
°C (77°F) [4 kΩ]
1.9 V
24
Air thermo sensor input
When sensor temperature is
25
°C (77°F) [1.5 kΩ]
2.2 V
25
Photo sensor ground
Ignition switch: ON
0 V
26
A/C pressure sensor
at 2.6 MPa
3.9 V
27
Ground
Always
0 V
28
Power supply to the ignition
switch (IG2)
Ignition switch: ON
Battery positive voltage
29
Air mixing damper control motor
potentiometer input
When the damper door is
moved to the MAX. HOT
position.
1.4 V
30
Illumination ground
Always
0 V
31
ILL power supply
Lighting switch: ON
Battery positive voltage
34
A/C pressure sensor ground
Always
0 V
36
Power supply to the ignition
switch (ACC)
Ignition switch: ON
Battery positive voltage
TERMINAL
NO.
CHECK ITEM
CHECKING REQUIREMENTS
NORMAL CONDITION
SPECIAL TOOLS
HEATER, AIR CONDITIONING AND VENTILATION
55-139
SPECIAL TOOLS
M1552000600334
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION
APPLICATION
MB991367
Special spanner
MB991367-01
Armature mounting nut of
compressor removal and
installation
MB991386 Pin
MIT217213
Armature mounting nut of
compressor removal and
installation
MB991658
Test harness set
Tool not available
Inspection of throttle position
sensor
B991367
MB991658
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст