Mitsubishi 380. Manual — part 804
SRS AIR BAG DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-140
STEP 1. Using diagnostic tool MB991958, diagnose the
CAN bus line.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
(1) Connect diagnostic tool MB991958. Refer to "How to
connect the diagnostic tool
."
(2) Turn the ignition switch to "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result satisfactory?
YES : Go to Step 2
NO : Repair the CAN bus lines (Refer to GROUP 54C,
Diagnosis-Can Bus Diagnostic Chart ). .
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Go to Step 3.
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
− How to Cope with Intermittent
Malfunctions ).
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SRS AIR BAG DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-141
STEP 3. Check the side-airbag module (LH). (Using
diagnostic tool MB991958, read the diagnostic trouble
code.)
(1) Disconnect the negative battery terminal.
(2) Disconnect the side-airbag module (LH) connector D-24.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into the D-24 harness side
connector by testprobe.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check the
diagnostic trouble code.
Q: Is DTC B1433 set?
YES : Go to Step 4.
NO : Replace the seatback frame of the front seat (LH)
(Refer to GROUP 52A, Front Seat
go to Step 6.
AC307778
CONNECTOR : D-24
AC
D-24 (R)
2
1
HARNESS SIDE
CONNECTOR
(REAR VIEW)
AC006042BP
MB991866
(RESISTOR HARNESS)
D-24 HARNESS SIDE
CONNECTOR
D-24 SIDE-AIRBAG
MODULE (LH) CONNECTOR
MB991865 (DUMMY
RESISTOR: 3
Ω)
SRS AIR BAG DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-142
STEP 4. Check the side-airbag module (LH) circuit.
Measure the resistance at the SRS-ECU connector D-27.
(1) Disconnect SRS-ECU connector D-27.
(2) Disconnect side-airbag module (LH) connector D-24.
CAUTION
Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(3) Check for continuity between D-27 harness side connector
terminals 9, 10 and body ground.
It should be open circuit.
Q: Does continuity exist?
YES : Go to Step 5.
NO : Erase the diagnostic trouble code from memory, and
check the diagnostic trouble code. If DTC B1433 sets,
replace the SRS-ECU (Refer to
). Then go
to Step 6.
24DB064A
CONNECTOR: D-27
SRS-ECU
D-27 (Y)
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
D-27 Floor
harness
connector
(rear view)
AC307778
CONNECTOR : D-24
AC
D-24 (R)
2
1
HARNESS SIDE
CONNECTOR
(REAR VIEW)
24DB078A
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
D-27 FLOOR HARNESS
SIDE CONNECTOR
(REAR VIEW)
SRS AIR BAG DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-143
STEP 5. Check the harness wires for short circuit to
ground between SRS-ECU connector D-27 (terminal No.9
and 10) and side-airbag module (LH) connector D-24
(terminal No.1 and 2).
Q: Are the harness wires between SRS-ECU connector
D-27 (terminal No.9 and 10) and side-airbag module (LH)
connector D-24 (terminal No.1 and 2) in good condition?
YES : Go to Step 6.
NO : Replace the harness wires between SRS-ECU
connector D-27 and side-airbag module (LH)
connector D-24. Then go to Step 6.
STEP 6. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1433 set?
YES : Return to Step 1.
NO : The procedure is complete.
AC307778
CONNECTOR : D-24
AC
D-24 (R)
2
1
HARNESS SIDE
CONNECTOR
(REAR VIEW)
24DB064A
CONNECTOR: D-27
SRS-ECU
D-27 (Y)
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
D-27 Floor
harness
connector
(rear view)
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст