Mitsubishi 380. Manual — part 38
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-149
POWER WINDOW MAIN SWITCH FUNCTION
The main switch is located on the driver’s door.
Raises the driver’s power window
When the driver’s power window switch on the power window
main switch is pulled up, the system energizes its respective
power window motor, and then the driver’s window glass rises.
Lowers the driver’s power window
When the driver’s power window switch on the power window
main switch is pushed down, the system energizes its respec-
tive power window motor, and then the driver’s window glass
lowers.
Lowers the driver’s power window by one-touch down
function
When the driver’s power window switch on the power window
main switch is pushed down fully, the system energizes its
respective power window motor, and then the driver’s window
glass moves to its lowest position.
Raises the passenger’s power window
When the passenger’s power window switch on the power win-
dow main switch is pulled up, the system energizes its respec-
tive power window motor, and then the passenger’s window
glass rises.
AC106705
ON
OFF
ON
OFF
UPPER SIDE
POWER
WINDOW
MOTOR
POWER
WINDOW
MAIN
SWITCH
DRIVER'S
POWER WINDOW
SWITCH UPPER
SIDE
AH
AC106705
LOWER SIDE
POWER
WINDOW
MOTOR
POWER
WINDOW
MAIN
SWITCH
DRIVER'S
POWER WINDOW
SWITCH LOWER
SIDE
ON
OFF
ON
OFF
AI
AC106706
ON
OFF
ON
OFF
LOWER SIDE
POWER
WINDOW
MOTOR
POWER
WINDOW
MAIN
SWITCH
DRIVER'S
POWER
WINDOW
SWITCH
LOWER SIDE
AC
AC106705
UPPER SIDE
POWER
WINDOW
MOTOR
POWER
WINDOW
MAIN
SWITCH
ON
OFF
ON
OFF
PASSENGER'S
POWER WINDOW
SWITCH UPPER
SIDE
AJ
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-150
Lowers the passenger’s power window
When the passenger’s power window switch on the power win-
dow main switch is pushed down, the system energizes its
respective power window motor, and then the passenger’s win-
dow glass lowers.
POWER WINDOW SUB SWITCH FUNCTION
The sub switches are located on the passenger’s doors.
Raises the passenger’s power window
When the power window sub switch is pulled up, the system
energizes its respective power window motor, and then the
passenger’s window glass rises.
Lowers the passenger’s power window
When the power window sub switch is pushed down, the sys-
tem energizes its respective power window motor, and then the
passenger’s window glass lowers.
Power window timer function
Even after the ignition is switched off, the ETACS-ECU keeps
the power window relay activated for approximately 30 sec-
onds, enabling raising and lowering of the power windows by
using the power window switches. After approximately 30 sec-
onds, the power window relay is deactivated.
During this timed operation, if the driver or passenger doors are
opened, the power window relay is deactivated from that
moment.
AC106705
LOWER SIDE
POWER
WINDOW
MOTOR
POWER
WINDOW
MAIN
SWITCH
ON
OFF
ON
OFF
AK
PASSENGER'S
POWER WINDOW
SWITCH LOWER
SIDE
AC106705
ON
OFF
ON
OFF
UPPER SIDE
POWER
WINDOW
MOTOR
PASSENGER'S
POWER
WINDOW
SUB SWITCH
UPPER SIDE
AL
AC106705
LOWER SIDE
POWER
WINDOW
MOTOR
PASSENGER'S
POWER
WINDOW
SUB SWITCH
LOWER SIDE
ON
OFF
ON
OFF
AM
AC200337AC
ON
OFF
ON
OFF
ON
(Open)
OFF
(Closed)
IGNITION SWITCH (IG1)
POWER WINDOW
RELAY
DRIVER'S OR FRONT
PASSENGER'S
SEAT DOOR
SWITCH
t
t: 30 seconds
t
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-151
INSPECTION PROCEDURE D-1: Power Windows: Power windows do not work at all.
NOTE: This troubleshooting procedure requires use
of diagnostic tool MB991958 and SWS monitor kit
MB991813. For details on how to use the SWS mon-
itor, refer to "How to connect SWS monitor
."
.
CIRCUIT OPERATION
The ETACS-ECU turns on the power window relay
(installed on the junction block) to activate the power
windows when the ignition switch (IG1) is turned to
the "ON" position.
.
TROUBLESHOOTING HINTS
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The power window relay may be defective
• The power window main switch may be defective
• The ETACS-ECU may be defective
AC305015
FUSIBLE LINK No.5
AI
16DB310A
CONNECTOR: C-12
16DB327A
CONNECTOR: C-219
JUNCTION BLOCK
(REAR VIEW)
16DB332A
3
9
4
12
14
6
13
5
1110
8
2
7
1
HARNESS SIDE
CONNECTOR:E-04
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-152
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: diagnostic tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
• MB991813: SWS Monitor Kit
• MB991806: SWS Monitor Cartridge
• MB991812: SWS Monitor Harness (For Column-ECU)
• MB991822: Test Probe Harness
STEP 1. Use diagnostic tool MB991958 to select "ECU
COMM Check" on the SWS monitor display.
Check the ETACS-ECU.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958. Connect special tool MB991910 before con-
necting special tool MB991812. Be sure to connect special
tool MB991806 after turning on special tool MB991824.
(1) Connect the special tool. Refer to "How to connect SWS
monitor
."
(2) Turn the ignition switch to the "ON" position.
(3) Operate the diagnostic tool MB991958 according to the
procedure below to display "ECU COMM Check."
a. Select "Interactive Diagnosis."
b. Select "System Select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "ECU COMM Check."
(4) diagnostic tool MB991958 should show "OK" on the "ECU
COMM Check" menu for the "ETACS ECU" menu.
Q: Is "OK" displayed for the "ETACS ECU" menu?
YES : Go to Step 2.
NO : Refer to Inspection Procedure A-3 "Communication
with the ETACS-ECU is not possible
."
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
COLUMN SWITCH
CONNECTOR
COLUMN SWITCH
CONNECTOR AT
HARNESS SIDE
MB991812
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст